jlpservicesinc Posted December 21, 2018 Share Posted December 21, 2018 A contour bandsaw is one of those tools where a skilled (master) can make it cut straight or curved to shape no matter what is thrown at it.. Novices on the other hand rarely can cut straight even with a new blade specd for the material and thickness.. My saw eats blades like they are candy especially with the cheap steels which have inclusions.. It really is one of the rarer tools, unlike a plasma, cutoff saw, table saw, etc, etc where the guide does the work and if it's set accurately will cut straight each and every time.. Quote Link to comment Share on other sites More sharing options...
Glenn II Posted December 21, 2018 Share Posted December 21, 2018 Made a reverse twisting jig today like I had seen on a link from this site. I'm quite sure I must have around 50 open end adjustable wrenches (crescent wrench.) Took me longer to find 2 of the same size and shape than it did to build the jig. (After the jig was done of course, I found wrenches everywhere I turned in my shop.) Then made a steak turner to test it out. Made from 5/16" 1018 square bar stock, wire brush and olive oil finish. Quote Link to comment Share on other sites More sharing options...
FivePointsForge Posted December 21, 2018 Share Posted December 21, 2018 On 11/30/2018 at 6:43 PM, FivePointsForge said: Thank you! The longer slender blade is a gift for a friend and is all planned out, the blade was forged from a piece of leaf spring from his old boat trailer. The handle will be made out of a piece of cherry from a handle from his late wife’s casket. Finished this one, wound up just forging some bronze fittings. Unfortunately I only got one pic of it before I rushed it out the door, it was a gift that I had to either give last night or not until after the holidays, so the epoxy was probably still sticky inside when I handed it over Quote Link to comment Share on other sites More sharing options...
Ranchmanben Posted December 22, 2018 Share Posted December 22, 2018 Got some Christmas presents handed over yesterday. A couple of fancy hammers with bois d’arc handles and one user 2lb rounding hammer. Also a knife with raindrop damascus I forged from 1084 and 15n20. Ebony scales and copper pins peened to fill the holes tight. Quote Link to comment Share on other sites More sharing options...
Reeltree Posted December 22, 2018 Share Posted December 22, 2018 Excellent work Quote Link to comment Share on other sites More sharing options...
DaMaakus Posted December 22, 2018 Share Posted December 22, 2018 I really like the engravings! And the raindrops look very good as well. Quote Link to comment Share on other sites More sharing options...
jlpservicesinc Posted December 22, 2018 Share Posted December 22, 2018 Amazing work Ben.. Quote Link to comment Share on other sites More sharing options...
58er Posted December 22, 2018 Share Posted December 22, 2018 very cool hammers. too nice to use Quote Link to comment Share on other sites More sharing options...
desmato Posted December 22, 2018 Share Posted December 22, 2018 I finished the 2 roasting forks for the aunt. (The ones I burnt my leg on) 3/8" sq. H.R. (blech) 32" tip-tip. Nothing too fancy. They will probably be left outside and abused by children. Quote Link to comment Share on other sites More sharing options...
FivePointsForge Posted December 22, 2018 Share Posted December 22, 2018 Those hammers are absolutely gorgeous. Like fine shotguns... Quote Link to comment Share on other sites More sharing options...
JHCC Posted December 22, 2018 Share Posted December 22, 2018 ...but requiring more precise aim. Quote Link to comment Share on other sites More sharing options...
DaMaakus Posted December 22, 2018 Share Posted December 22, 2018 Desmato, your work is really neat! Not sure what to think about the "kids will play with the pointy metal bars", though. Quote Link to comment Share on other sites More sharing options...
58er Posted December 22, 2018 Share Posted December 22, 2018 Christmas gift for wonderful wife. Quote Link to comment Share on other sites More sharing options...
Enewguy Posted December 22, 2018 Share Posted December 22, 2018 Very nice Quote Link to comment Share on other sites More sharing options...
psacustomcreations Posted December 22, 2018 Share Posted December 22, 2018 I frequently make my other projects out of scrap metal and did the same with these. A spring fuller that still needs the 1/2" round bar added and a hot cut from an old axe head. After that it was time to practice simple leaves and trying to make them into curtain rod holders. Another 92 more of these and I may get some that are acceptable. Suggestions for improvement are always welcome. Quote Link to comment Share on other sites More sharing options...
Daswulf Posted December 22, 2018 Share Posted December 22, 2018 All kinds of great work. Wow. PSA, a chisel to "vein" the leaves will give them a bit more realism and life. The shape ain't half bad. Quote Link to comment Share on other sites More sharing options...
Cannon Cocker Posted December 22, 2018 Share Posted December 22, 2018 I've been wanting to try a ram's head for a while so I have it a try today. It still needs wire brushed and treated. I'm pretty pleased with the results while knowing that there's a lot of room for improvement. If anyone has tips or suggestions for these I'd love to here them! This one decided to be a steak fork for the grill, but here soon I'll have a set of fire tools. Quote Link to comment Share on other sites More sharing options...
psacustomcreations Posted December 22, 2018 Share Posted December 22, 2018 Thanks Das. I am going to start adding chiseled lines soon. I think I have only made eight leaves so far total and very few other items so I am trying to learn a little at a time. Quote Link to comment Share on other sites More sharing options...
jlpservicesinc Posted December 23, 2018 Share Posted December 23, 2018 58er: Nice work.. Nice level of detail and it looks well thought out.. did you run a sketch ahead of time or on the fly design? Quote Link to comment Share on other sites More sharing options...
Daswulf Posted December 23, 2018 Share Posted December 23, 2018 1 hour ago, psacustomcreations said: I am trying to learn a little at a time. Best way to do it. I tried flat sharper chisels at first but like one I made that has a slight roundness to the cutting edge and leave it a little dull. With the slight roundness its easier toget in the previous mark to move it on and too sharp and you might chisel it in half. Sorry I have a photo of it somewhere here but not on my newer phone to post easily. It is made from coil spring, so an easy material to source. Quote Link to comment Share on other sites More sharing options...
Rojo Pedro Posted December 23, 2018 Share Posted December 23, 2018 My first basket twist. I split it with a chisel that I made so it was extra fun! Also made a snake that got his head run over out of an old file Quote Link to comment Share on other sites More sharing options...
Cannon Cocker Posted December 23, 2018 Share Posted December 23, 2018 I like that split basket twist Rojo. I almost did that too the steak fork I made earlier today but decided not to........ Now I'm wishing I did. Oh well, I guess that gives me an excuse to make another one! Quote Link to comment Share on other sites More sharing options...
Ranchmanben Posted December 23, 2018 Share Posted December 23, 2018 Thanks everyone. I can’t take credit for the engraving though. My dad did that work. He’s tried to teach me but I haven’t knack, some people can hammer steel and some can carve it. The knife was a fun change of pace. The Damascus was very fun to make, I can see how people get sucked into making elaborate patterns. I’m going to be playing with it more. Quote Link to comment Share on other sites More sharing options...
ausfire Posted December 23, 2018 Share Posted December 23, 2018 Some wonderful work over the last few posts. Inspirational! Ben, those hammers are exceptional. How lucky are you to have your own personal engraver on hand to put the finishing touches to your work! I have just been doing the same old fire pokers, bottle openers, toast forks, cobras, keyrings and endless bull and ram head designs. That's what the tourists like and they do sell well. After today's demo, I decided to try a couple of those knots in 6mm round, after seeing the ones posted here. I messed the first one up (left) but it still made an interesting shape so I kept it. The other three in the picture worked better. Interesting to see the difference in texture between the old wrought iron and the mild. Looking forward to a day off the forge on Christmas Day .. back again on Boxing Day. (Our first grandson was born last week and we are off to Townsville for Christmas Day) Hope everyone on here has a safe and happy Christmas. Quote Link to comment Share on other sites More sharing options...
58er Posted December 23, 2018 Share Posted December 23, 2018 jlpserviceinc:-thanks...just on the fly...not very good in the drawing dept. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.