Jason L Posted December 9, 2023 Share Posted December 9, 2023 I tested out my new welder today. I bought an Arccaptain Mig130 because I needed a light duty welder to tack things together from time to time. I got everything out and started with the wire and I was horrible. I couldn't see the joint and the welds were all over the place. It was as ugly as a mud fence. I wear bifocals and the bottom of my glasses weren't high enough for me to see through the hood lens. After trying to prop up my glasses with paper towel under the bridge, I was just about to give up when I noticed my hood had an adjustment on the top strap which I hadn't paid attention to before. I didn't even notice there was a top strap. After adjusting it, I almost got that stack of dimes I was looking for. 100% improvement. I haven't welded in many years so there's still lots of room for improvement but now that I have everything dialed in, I'm going to work on it. That's one great little welder for the money. I'm a happy guy. Quote Link to comment Share on other sites More sharing options...
JHCC Posted December 10, 2023 Share Posted December 10, 2023 Some more chasing tool making. Quote Link to comment Share on other sites More sharing options...
aaamax Posted December 10, 2023 Share Posted December 10, 2023 (edited) Nice. how do you go about making that crescent moon shape? the only way I can make such detail is with a dremmel. Edited December 10, 2023 by Mod34 Excessive quoting Quote Link to comment Share on other sites More sharing options...
JHCC Posted December 10, 2023 Share Posted December 10, 2023 There are two ways: one is to make a round bevel on one side of the tool and a flat bevel on the other (L), and the other is to make the hollow with a Dremel or an appropriately sized round file (R): Douglas Pryor has a video about making the former kind of curved liner: https://youtu.be/Q4Kbz5yz5XQ?si=In8INcr9UrL6XwAY Quote Link to comment Share on other sites More sharing options...
Arthur210 Posted December 10, 2023 Share Posted December 10, 2023 A spoon: Quote Link to comment Share on other sites More sharing options...
GhostTownForge Posted December 10, 2023 Share Posted December 10, 2023 and a very nice spoon at that! Quote Link to comment Share on other sites More sharing options...
alexandr Posted December 10, 2023 Share Posted December 10, 2023 It got warmer, only -15 C. I can go to work. The lantern on the wall is more than 20 years old. Quote Link to comment Share on other sites More sharing options...
Bud in PA Posted December 10, 2023 Share Posted December 10, 2023 Jason L I welded in a machine shop years ago, I had the same problem with my bifocals. Switched to no line bifocals, problem gone. Quote Link to comment Share on other sites More sharing options...
bluerooster Posted December 10, 2023 Share Posted December 10, 2023 Arthur210, That's a real nice spoon. Today I pinned the tongs together, and made some adjustments. I'm not satisfied with them at all. Made another set following a video on YT. (Thanx Jennifer) and I think they will do way better. still have some tweaking to do, but I can tell already they are a vast improvement over the method i was using. Even the rivet came out better. Alexandr, I like those "fleur de lis" brackets on the beams. That's a nice touch. But -13c is way too cold for me.;) Quote Link to comment Share on other sites More sharing options...
JHCC Posted December 10, 2023 Share Posted December 10, 2023 2 hours ago, Bud in PA said: Switched to no line bifocals, problem gone. I have no-line bifocals, but my problem is that my working distance correction is between those for reading and for distance. I’ve found it’s easier simply to wear non-correcting safety glasses at the forge and under the welding hood. Quote Link to comment Share on other sites More sharing options...
Irondragon Forge ClayWorks Posted December 10, 2023 Share Posted December 10, 2023 I had the same problem with my bifocals when welding, went to my Optometrist to get a new prescription. He advised me that he could write a new one, but it wouldn't help much. He said it was time to get my blacksmith cataracts fixed. I made an appointment with the eye surgeon who fixed Debi's cataracts. He advised he would be able to correct my vision to 20/25 with lens implant's and the only time I would need cheater glasses was for fine print and very close work. He is a very experienced Ophthalmologist with over 6000 procedures to his credit. Had them taken care of, the first eye the day after my birthday and the second one two weeks later. After a short rehabilitation, using eye drops and zero problems, I could not believe the difference. It's like my eyesight was when I was in my 30s clear as a bell and the difference in colors is amazing. I can actually see to weld and I can see the sights & target with my muzzleloaders and duty weapons without corrective glasses. The only draw back is, I have to wear safety glasses as my bifocals were safety lenses and I had them on all the time. I can't control the wind, all I can do is adjust my sail’s. Semper Paratus Quote Link to comment Share on other sites More sharing options...
Frosty Posted December 10, 2023 Share Posted December 10, 2023 I bought a stick on magnifying lens for my welding shield, my trifocals let me see okay but I can't get close enough and still keep the mig torch in play. Frosty The Lucky. Quote Link to comment Share on other sites More sharing options...
Goods Posted December 10, 2023 Share Posted December 10, 2023 I have to get a better welding helmet myself, or at least a new lens for the on I have. It’s too dark and I can barely see the bead, let alone the joint I’m trying to weld. this afternoon, I forged out a long steak flipper for my neighbor as a Christmas gift for his brother. (It good to be kind to your neighbors!): Keep it fun, David Quote Link to comment Share on other sites More sharing options...
Frosty Posted December 10, 2023 Share Posted December 10, 2023 I bought an inexpensive auto darkening welding mask a few years ago and you can adjust how dark it gets. A twist of the little dial and it goes from #4 to #14 shield. Coupled with the magnifying stick on and I can see pretty well, won't be passing any certification tests though. <sigh> Frosty The Lucky. Quote Link to comment Share on other sites More sharing options...
BillyBones Posted December 11, 2023 Share Posted December 11, 2023 A;exandr, as always splendid. One of of co-workers has taken up woodworking. He asked about lathe tools so i made him this gouge. Made of 5160. Copper collar with a brass rivet. Burned the tang into the handle the epoxy filled. The handle is from a mop that was getting thrown out at work. Quote Link to comment Share on other sites More sharing options...
jlpservicesinc Posted December 11, 2023 Share Posted December 11, 2023 Nice work ya'll.. Spent some time figuring and learning.. Quote Link to comment Share on other sites More sharing options...
JHCC Posted December 11, 2023 Share Posted December 11, 2023 Spent some time making tooling for a commission. First, a bending tool for pipe: Which works both pulling: And pushing: And welded up a flatter fit the fly press, to turn round pipe into oval handrail: I think I’ll use this to flatten the handle on the bending tool, for more positive alignment of the grip. Quote Link to comment Share on other sites More sharing options...
jlpservicesinc Posted December 11, 2023 Share Posted December 11, 2023 JHCC How can the bar be held straight without twisting with the lugs on the sides of the bar? I looked into a bender like this 30 years ago and could never get it to work.. Maybe my hands aren't strong enough.. it always wanted to twist in my hand.. Quote Link to comment Share on other sites More sharing options...
JHCC Posted December 11, 2023 Share Posted December 11, 2023 It does want to twist in the hand, and I’m hoping that squaring up the handle will help. If that doesn’t work, I’ve got an idea for a different design that might work better. More to come…. Quote Link to comment Share on other sites More sharing options...
Daswulf Posted December 11, 2023 Share Posted December 11, 2023 Now that you have the flatter for pipe, slide an oval section on the handle and weld it up. Quote Link to comment Share on other sites More sharing options...
jlpservicesinc Posted December 11, 2023 Share Posted December 11, 2023 Jhcc. The one I made I put a jog in the handle. Aka dogs leg. This helped but in use it still wasn't as accurate. . Going with the jaws in line with the handle ended up being the best option use wise, but was lack luster so thru it in the scrap pile. Quote Link to comment Share on other sites More sharing options...
Dragonfireforging Posted December 11, 2023 Share Posted December 11, 2023 Hello I’m 16 and live in Arkansas. I am a. Beginner blacksmith and am looking for an apprenticeship. Is there anyone that is accepting. have you tried a leather or felt wrap around the handle it might help with grip. If that doesn’t work try making grooves that your fingers can sit in when you hold it. Quote Link to comment Share on other sites More sharing options...
gewoon ik Posted December 11, 2023 Share Posted December 11, 2023 Finished the small shovel Happy but some small improvements are needed for the next one. Also not happy on ending the handle. Quote Link to comment Share on other sites More sharing options...
George N. M. Posted December 11, 2023 Share Posted December 11, 2023 If this is designed as a garden trowel I would say that the planes of the shovel blade and the handle should be closer to parallel. "By hammer and hand all arts do stand." Quote Link to comment Share on other sites More sharing options...
Frosty Posted December 12, 2023 Share Posted December 12, 2023 I'm with George, the bends in your handle are WAY too pronounced, a garden trowel should have a much flatter handle to blade relationship. (Parallel) works. Frosty The Lucky. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.