brickman Posted April 30, 2017 Share Posted April 30, 2017 not gonna lie, got super lucky with this sodorfors find.. Quote Link to comment Share on other sites More sharing options...
jdawgnc Posted May 12, 2017 Share Posted May 12, 2017 Here's my 300lb PW(I think) and it's little brother the 100lb mousehole. Check out the stand for the big guy, it's filled with sand and the anvil rests on a floating board so I can raise or lower it as necessary. Between that and the silicone on the heel I reduced the ring to a somewhat bearable tone. Before it was totally deafening. I did notice the rebound suffered a bit when I dropped a ball bearing on it after sitting it on the sand. It still moves metal just fine though, and I'll take a little less rebound in exchange for my eardrums! Quote Link to comment Share on other sites More sharing options...
Tooler Posted May 19, 2017 Share Posted May 19, 2017 I made this Rail anvil for a Lady friend Mechanical Engineer so she would have a tool her boyfriends did not. She wanted it red. 1956 G&E Shaper Quote Link to comment Share on other sites More sharing options...
Latticino Posted May 19, 2017 Share Posted May 19, 2017 52 minutes ago, Tooler said: I made this Rail anvil for a Lady friend Mechanical Engineer so she would have a tool her boyfriends did not. She wanted it red. 1956 G&E Shaper Extremely nice job. I have a similar one that I inherited from my father in law that I use for jewelry projects, though mine has a hardy hole. Might want to put in a prichel hole at least. It also looks like you may have welded on a top plate. If you did, was it a full penetration weld? What kind of steel did you use for the top plate? How did you heat treat it? Quote Link to comment Share on other sites More sharing options...
Tooler Posted May 19, 2017 Share Posted May 19, 2017 Latticino, Thanks for the compliment. Yes there is a top plate welded with both plug and deep beveled joints. Build ups on the horn and heel. No heat treatment or holes needed for the final usage/purpose here. Just an excuse to run the shaper and leave a little something for a young Engineer I mentored for a short while. If she needs a hole in it, she is capable of doing it. Quote Link to comment Share on other sites More sharing options...
JSlayer Posted June 20, 2017 Share Posted June 20, 2017 I picked up this 200lb Fisher-Norris Eagle at a farm estate auction over the weekend. Here's some before and after the clean-up shots. Quote Link to comment Share on other sites More sharing options...
jlpservicesinc Posted June 20, 2017 Share Posted June 20, 2017 Congrats.. Looks great.. Quote Link to comment Share on other sites More sharing options...
offgrid Posted June 21, 2017 Share Posted June 21, 2017 Just recently bought this Peter Wright 141lb. Finished the stand today. Quote Link to comment Share on other sites More sharing options...
Paul Ehrlich Ashman Posted July 12, 2017 Share Posted July 12, 2017 Lucky score for me, a friend at church told me his dad had this sitting behind his house. This is how I got it, 120 pound Vulcan, has a 44 on it also, I'm guessing the year? Paid $150 for it. Counting myself very fortunate! Quote Link to comment Share on other sites More sharing options...
Jacksman Posted July 19, 2017 Share Posted July 19, 2017 Here are three I got lately: A 200 lb. + American Star Hornless A 110 lb. Atwood A 152 lb. Peter Wright I picked up the American Star on a camping trip in Michigan and got the other two at local auctions. Quote Link to comment Share on other sites More sharing options...
D Michael McIntyre Posted August 3, 2017 Share Posted August 3, 2017 I hammered a lot of metal (mostly copper) on a plain piece of railroad track for 20 years before finally convincing myself to take the plunge on a real anvil. Wow! This 50 kg Kanca isn't to everybody's taste, but I would kick my wife out of bed and sleep with this thing if I wasn't afraid of banging my head on one of the horns. I fashioned the stand out of an old waterbed frame I picked up curbside longer ago than I can remember. I secured the anvil to the stand by hand routing a custom fitting cap. This setup has been a beast so far, and I am really pleased with how this all turned out. Quote Link to comment Share on other sites More sharing options...
Jackdawg Posted August 3, 2017 Share Posted August 3, 2017 nice looking anvils those. Quote Link to comment Share on other sites More sharing options...
was45 Posted August 7, 2017 Share Posted August 7, 2017 i have two anvils at work i hope you guys can help with one is a small english if you go by the numbers on it,it weighs 580lb the big one is 896lb i cant seem to find a makers mark on them and for the life of me i cant find anything close to 896 lb on the net.could you help with a valuation on them Quote Link to comment Share on other sites More sharing options...
Lou L Posted August 7, 2017 Share Posted August 7, 2017 If you ship the small one to me I'll give it a thorough inspection and report back. Quote Link to comment Share on other sites More sharing options...
ThomasPowers Posted August 7, 2017 Share Posted August 7, 2017 Can you tell us what country they are located in? I'm at work in Mexico right now; but I feel you probably don't want a value in pesos. Quote Link to comment Share on other sites More sharing options...
customcutter Posted August 8, 2017 Share Posted August 8, 2017 I got this PW from a blacksmith a few days ago. It's been repaired around the hardie and pritchel holebuwhere a small section of the top plate broke out best I can tell, but he said he's used it for years with no problems. He also said if it ever gave me problems, to come see him. She's my first, so I think she's a beat... She's marked 1 2 17, so 185#. Very interesting how the repair was done. It rings true, and rebound is almost as good as the rest of the anvil, which I think is near 90% just bouncing a ball pen hammer on the face, and 80% in the repaired area. Quote Link to comment Share on other sites More sharing options...
ThomasPowers Posted August 8, 2017 Share Posted August 8, 2017 Looks good to go for another generation or 3... Quote Link to comment Share on other sites More sharing options...
grimm1966 Posted August 16, 2017 Share Posted August 16, 2017 Here is my anvil that I purchased new in 2006. It's a Old World double horn classic at 165 pounds (75 kilos). I use it to make armour and now, finally, I have a forge to go with it so I can do hot work as well. Quote Link to comment Share on other sites More sharing options...
jjhend28 Posted August 19, 2017 Share Posted August 19, 2017 Been a while since I posted anything on here, school and work has me busy! But I just made this sweet little acquisition. Got it for a sweet low price of 0 dollars. As far as I can tell this is a 107lb Haybudden blackjack anvil made for Simmons hardware in St. Louis. Quote Link to comment Share on other sites More sharing options...
Jclonts82 Posted September 10, 2017 Share Posted September 10, 2017 Just finished mounting up my newest anvil to a big salt cedar stump I cut down. Decided to put the prevoius anvils on top for the fun of it. Bottom is 253# hay budden Middle: not sure of the make... never looked into it, but made all of my projects have so far been made on it, save the first 3-4 cotton picker spindles I messed around with on the top little guy. Top: first time I actually looked at markings and serial numbers was when taking this pic... whaddya know, also a hay budden. Question: Did hay budden ever make a cast iron only anvil? On my little ( 30#?) anvil I don't see a welded on top plate of steel, so its either all iron, or all steel... any thoughts? Quote Link to comment Share on other sites More sharing options...
RobS Posted September 10, 2017 Share Posted September 10, 2017 Middle anvil looks like a Columbian. The later Hay Buddens, after 1908, were solid forged steel top half. Someone more informed may be able to clarify, but I think Hay Budden also did some solid one piece cast steel. I believe they had a "SS" with the serial number. Quote Link to comment Share on other sites More sharing options...
Bigmatt Posted September 10, 2017 Share Posted September 10, 2017 Hay all, new to the forum! My wife thinks I'm crazy for being excited about my first "real" anvil! But I found this on Thursday. Quote Link to comment Share on other sites More sharing options...
JHCC Posted September 10, 2017 Share Posted September 10, 2017 1 minute ago, Bigmatt said: Hay all, new to the forum! My wife thinks I'm crazy for being excited about my first "real" anvil! But I found this on Thursday. Circa 1830-1835 Mousehole Forge -- one of the best anvils ever made. Good score! I must note, however, that the edges are suspiciously sharp for an anvil of that vintage, and it looks like there might be some repaired areas on the edges and the heel. Have you tested it for rebound? Are the rebound and ringing consistent over the entire face? (Oh, and welcome to IFI! Please go to the Introduce Yourself page and let us know who you are, but please READ THIS FIRST.) Quote Link to comment Share on other sites More sharing options...
Bigmatt Posted September 10, 2017 Share Posted September 10, 2017 I bounced a 1 inch ball bearing on it and bounced back to my hand. The guy I got it from said he had it for 25 years and never used it. Quote Link to comment Share on other sites More sharing options...
Reeltree Posted September 10, 2017 Share Posted September 10, 2017 rebound is good,, I will say the horn and shelf area has noticeable dings in them from usage, and the top and edges shows very little Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.