Goods

I would stay on the smaller side for the shop vacs. Scale and grinder dust gets heavy fast! Keep it fun, David

If you’re wanting to support a local smith, you could post to the “Indiana Blacksmith Association (IBA)”Facebook group. I’m sure one of the guys there is jump on it. Expect the same questions, so you may want to put all the information in your first post. Keep it fun, David (IBA member)

For file guides, I saw an interesting trick on YouTube. The person took a cheap ceramic kitchen knife and cut it with a diamond abrasive wheel to make the faces of the file guide, which he epoxied in place. I’m not sure how long it will hold up, but it look like a good idea… Keep it fun, David

I agree on the hat rack, but again it’s not my style. I am really drawn to the clean lines and simplicity of the crosses. Keep it fun, David

If I had to guess, I’d say they were MiG welded then wire wrapped. I like the idea of slit and drifted with a heat shrink fit. Not sure what to think about the hanger. It’s just not my style… I would agree with you that it needs a little more of something. Keep it fun, David

Keep in mind that using acid to dissolve coating that may be hazardous make the acid itself hazardous waste. If the coating is cadmium, it could take a lot stronger acid to dissolve it off. If it does the waste created is much more hazardous than if it was hexavalent chromium which is your typic yellow zinc plating that is pretty nasty in it own right. Keep it fun (and safe), David

Dave, the demo was at Fort Vallonia Days in Vallonia, IN. John/George, I have never setup at a craft fair. So far, I have only done sales at demonstrations and only if sales are allowed or even expected. Either way, I would be traveling to and packing a lot of gear, the inventory is minor compared to tools and materials. So, the sales are a nice benefit that goes a long way towards offsetting my costs. Personally, I have received many opportunities for commission work, but passed most of those asking to the other smiths who are more suited to commission work. Between work, family, and other responsibilities I can’t always guarantee time in the forge. At this point I’d rather forge the items I’m interested in to my liking and hope that someone would have interest in them, if I’m willing to sell them. Keep it fun, David

I picked up a patina forging in the sun this weekend, although its not what I would call “rainbow”. Keep it fun, David

George, it really felt like the sales were lower that last year for me. The smith I was with seemed to be doing pretty good. However, when I got home and counted the revenue, I came out a little better that last year’s total. I think the main difference was having more inventory, so even with better sales, I had more to take home. Of all the items I forged during the demo, only one of the fire pokers were left unsold. Honestly, these events aren’t about sales for me. The main reason for me to attend is the demonstration itself. The sales are just a bonus. (This is only a hobby for me, and I’m really not wanting to take the enjoyment out of it.) Keep it fun, David

The demo went well this weekend. I haven’t taken many pictures before, but I got a couple this time around. Basic pictures of the setup (not the best pictures…): Here are a couple of the items made while demonstrating: BBQ fork and spatula as well as the a few leaf key chains and pendants. This flower was going to be just a key chain. It just kept growing, with the aid of a few forge welds. Overall, the crowds weren’t as big as last year, but a lot of people seemed interested and the weather was good. It is a completely open air forge, so it would have been a lot easier if it was cloudy all day. Two full days of forging and interacting with the crowd made for a pretty good weekend! I’ll try to get better pictures of the setup next time. Keep it fun, David

Will the joint on the hood rotate? If so that should give you a vertical connection. If not, I would cut that off square and put a 45 elbow on it. You may even be able to get a straight adapter to replace the 45 degree adapter that is on it now. Keep it fun, David

Here is another example, but not really suited to the end of a bar: Keep it fun, David

JLP, no I haven’t started a journal, but I need to. I’ve got one in the shop for that purpose, particularly for keeping track of steps/sequences and dimensions that work out good for me. I just get rolling and don’t take the time to write things down. It comes back to bite me when I try to make the same item a year later… (I would be a little scared to see how much time I have in some of these items.) Chad, I like your scoop! Doing these in batches makes consistency a little easier. The side profile is pretty close on these, but the top profile, eye transition and blade thickness/taper, varies considerably. Most of that was me trying to get the process down for the eye transition I want. Still not quite there yet. (Another reason I should be using that journal!) The knives I pretty much have the process down, but I also work these through step by step in batches. (Cut all the blanks the same, marked the set down at one time, drew all the handles out… they’re small, so not really wasting residual heat between steps. I’m not sure I would have the same efficiency on something larger like hatchets.) Keep it fun, David

For my large quench tank (basically 5gallon steel bucket with about 4gallons of oil), I just heat up an old sash weight to a red heat and that usually gets me pretty close to 120F. For my small quench tank (3” Square tube about 15” tall filled to 12”) I just heat it up with a propane torch. Both methods don’t take much time or effort…) Keep it fun, David

All the forging, heat treating and sharpening is done: (Tomahawk at the bottom has a little bit of delamination that showed up at the quench , but it’s not too bad. It may end up as my target hawk…) Now on to leather work… 3 days till the festival! Keep it fun, David

I watched a YouTube video of the guys at Coal Iron Works talking about the effort that has gone into the self contained hammer and at the quad state they did an introduction/unveiling of it looking for feedback. Even with serious engineering work, it needs a lot of fine tuning. (I should have made it to quad state to hang out with them. I would have love to see Kurt putting it through a work out… Keep it fun, David

8” double wall may not fit inside a 10” vent pipe. Might want to check before committing… Keep it fun, David

The other thing to remember is that most of the modern ceramic belts need fairly high pressure to stay sharp. As the ceramic dulls, the high pressure causes fractures creating new sharp edges to cut with. If the pictured grinder was available for $50, that would probably be a good starting point. Not as flexible as the “modern” knife maker type grinders, but you could get a lot of work/learning done with it. Keep it fun, David

Do you have an image of the grizzly 2x75? They have a couple different styles listed on their site. One or two of them look like they would work, but may be under powered. The others I wouldn’t mess with… They also listed the belt size as adjustable from 2x72 to 2x79, on at least one model. Keep it fun, David

George, we absolutely love this house. I drove past it every day going back and forth to work for ten years. Then it went up for auction in the last recession and we got it for a very good price. We’ve put a lot of time and money into over the past 15+ years, but it has been well worth it. I could go on and on about the property… (It was a good place to be stuck during the height of the pandemic! I can’t imagine how people living in apartments/condos survived that time period.) Keep it fun, David

This is extent of my Halloween decorations: Ive always thought it would be neat to fabricate arms with claw like fingers, but I’m afraid the effort to get the effect I want would take the fun out of it… Keep it fun, David

So, what realistically, is your budget? You can get a reasonably good grinder on Amazon for under $700~$1200. Mine is on the bottom end without out a VFD and it does fine. I would love to have one with a VFD and more attachment options, but this does what I need for the time being. What you need to what out for is the cost of belts, they are consumable items… Keep it fun, David

Don’t run you mixing tube larger. That will lower the velocity, and increase the chances of the flame front moving into the mixing tube. The flame front has a fixed velocity, if you lower the fuel/air velocity, you could run into problems. (Even if it works, that will reduce your turn down capacity, you may not want to run it at full heat all the time.) Better to reduce the bell size, but I will definitely defer to Frosty! Keep it fun, David

I’m not a gas forge guru, but I’m guessing that the bell reducers you’re using as nozzles are too large of diameter change from the mixing tubes. This will cause the flame to settle in at the change in diameter, heating the bell significantly. Try using pipe coupler, or thread protectors (Frosty’s favorite), or just form you nozzle in the refractory of the forge. (You do have the ceramic blanket covered with a refactory right?) Frosty, Mikey, what are your thoughts. Keep it fun, David

No, I was out of town with family all day Saturday. I heard about Josh’s demo, but nothing not John’s. I bet John’s was interesting! (He was doing inflatable’s…) Keep it fun, David