Jump to content
I Forge Iron

Old Japanese Sword Rescue


Steve Shimanek

Recommended Posts

I recently bought this from another blade smith, who took it in trade for some blade work. He said it had been used for brush cutting by the person he got it from (not the best use obviously.) The photos show a lot of problem areas, not the least of which was the amateur grinding to "sharpen" it; 2 major delaminations near the sharp edge, 6 or 7 major bends, reduced point area, etc. The shape pointed to a potentially old sword, so i took a gamble on it, though i didn't pay much for it. After a couple of sessions with the roughest traditional water stone, I believe it to be an older traditionally made blade. The first photos are from the seller, as it arrived; i will post additional photos as the work progresses. Nihonto are a specialized area; i do not recommend just anyone to try their hand at restoration.

geoffsugata.jpg

geoffkissaki.jpg

geoffkat.jpg

geoffblister.jpg

geoffnakago.jpg

geoffnakago2.jpg

Link to comment
Share on other sites

  • 2 weeks later...

Lots of challenges on this blade due to condition and abuse....blade was straightened, proper geometry restored, and brought to the best condition possible. Rescued from the fate of being turned into a tanto or cut up and restacked by the previous owner, and being used to cut brush by the owner before that. Seems to be a Sue Bizen kazuuchimono mass produced blade from the mid 1500s.

kiss fixed.jpg

kissfixed2.jpg

kissfixed3.jpg

kattired.jpg

monouchireshape.jpg

nakagoresto2.jpg

nakagorev.jpg

Last 2 photos....

sugatafixed.jpg

sugatafixed2.jpg

Link to comment
Share on other sites

It is a bit tired and beat up, but deserving of being treated with some dignity and respect; this is the second blade i have I have bought /rescued with the help of the same bladesmith. The other one has turned out much better as the starting condition was not as bad. Being in the Pacific Northwest, he comes across these blades and i am in the right place to acquire them on occasion.

Link to comment
Share on other sites

I do not think it is signed by a maker; either it is obscured by rust, signature was cut off when shortened, or it was never signed... when more rust is removed i will be able to see if there is a signature, but it is doubtful.   My guess as to manufacture is posted above and is the best i can do currently.

Link to comment
Share on other sites

I seen the post with the maker listed. Mid 1500's is what made me think it would have a signature or armory marking. Great job restoring a poorly treated tool. Why a person would misuse an old sword like that is beyond me. It's like blocking a broken window with a four hundred year old etching. 

Pnut

Link to comment
Share on other sites

14 hours ago, Bo T said:

I might be imagining it, but there seems to be a slight 'quench line' above the edge? Especially towards the tip? 

Bo T; there is a hamon and boshi (hardened tip and edge) on the sword, but it is difficult to see unless you know what to look for.....most hamon are more obvious, but this one may have faded from excess heat when it was abused by grinding, or never had much visual pop from the beginning when it was made...it is hard to say which.

As to the lack of signature: is is possible  that this sword was longer when it was made, and the signature was lost when it was shortened; or, it was never signed at all and was issued out of an armory for the cannon fodder troops; or, there may be a signature hiding under all of the rust.

Thanks for the comments.

Link to comment
Share on other sites

When I mentioned cannon fodder troops, i was referring to the Sengoku period in Japan in the 1500s; how it came to the US is unknown, but i think it likely it was captured in WW2 and was a GI bringback....as such, it would have been carried by an officer. The Japanese NCO swords were machine made from modern mill steel, not made traditionally as this sword was. Thanks for the comment.

Link to comment
Share on other sites

I’d love to know whether you’re going to make a traditional tsuba for it.  I tried watercasting copper and other non-ferrous metals a while ago and was pleasantly surprised by the results. I understand that a traditional tsuba starts life as a water cast disc of copper/brass/silver which is then hand engraved. Great that you’re breathing new life into it. 

Link to comment
Share on other sites

In ancient times in japan, there were habaki made of iron, but since at least around 900 ad they have been made of copper, occasionally solid silver or gold, and sometimes covered with those materials. Tsuba were occasionally made by the swordsmiths, but this was not common, particularly from the later 1500s on. As TP and Pnut state, the various parts were usually made by specialists, even in Japan today. Western people like myself have limited access to these specialists (or the desire to pay for them) and so try to replicate their work, usually with limited success:blink: I will be making a habaki and putting the sword in shirasaya; i have too many projects at the moment to make a full koshirae for this sword, as i have other koshirae projects ongoing for other swords currently.

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...