keithgartner

I'm proud to welcome you to IFI. I also wish you a speedy and complete recovery. Nakedanvil ( Grant Sarver ) Is ( in my opinion) our resident induction guru ( sorry Jock ). He will probably reply to your post, if not though, send him an e-mail, find him on the members list. Good luck in everything you do. Keith

I'm planning on going Sat. to walk through. I'll be the 6'8" guy wearing blue Carhart bibs and a dumb look on my face.

You cannot draw through the home appliance regulator, (that's what's running your water heater and must stay in line) tee into the fuel run before that regulator, and install your forge regulator. Or get a separate bottle (tank) for your forge.

Thank you for your thoughts, prayers, condolences, they really do mean a-lot, and help. Dan, please accept my condolences for the loss of your Christopher. Wayne, I hope everything is going well now, it is a roller coaster ride of emotions, savor the highs but don't despair in the valleys. Steve, there are no petty problems, when it comes to our children's health, nor the emotion every parent feels when one of ours is ill, I'm so happy your son is better. Again THANK YOU ALL Keith

Easilyconfused, actually isn't. That's all I do, use them more. My tools, rust some over winter. 1000 degree steel going into the slake tub doesn't help.

My son Eric has had Nephrotic Syndrome, since he was 18 months old, 1984. In 2001 in a 9 hour operation, that was supposed to take 6 hrs., he recieved my wifes kidney. That transplant lasted about 8 months, then his body rejected it. He was understandibly bitter and would not accept living donors from any of us for a new transplant. Through all this he played bantam and high school football, at the same time he was on the chess team. After high school, though he could have chosen disability, he delivered pizzas for Pizza Hut, and went on to manage that store. after awhile he got a union job at Integram, a seat supplier to the Chrysler plant in Fenton, MO. We know where that went. These were both night jobs because he underwent dyalisis for 6 hrs. every other day.On January 18, 2010. he took his own life, jumping off a bridge over the Missouri River. His body was found 2 months later, this past Thursday, March 18 almost 75 mi. downstream in the Mississippi River. Eric never got close to the top of the transplant list. Please become a donor. I'm trying to get back to the smithy.....

Steve, so sorry to read this, I have been away from IFI, and smithing all winter. Having fought kidney disease with my son, for over 25 years, and one failed transplant. I know the anguish you went through. Your son and entire family are in my prayers. Keep a close watch on the diet. Keith

You will have to wash all the oil off before the vinegar. I would wash it with dish soap and hot water, rinse well, put it in something plastic, a wheel barrow, Rubbermaid tote, even a heavy plastic trash bag, use at least 2 gals. of vinegar ( three if you use a wheelbarrow ) fill with water, let it sit a few days............rinse with water and wire brush, WD40 it immediately while still wet. Also I wouldn't get in too much of a hurry to "repair" the top face, you'll be surprised how good it works as is. Keith

GEORGE; Jock Dempsey has some lessons in I-Forge, on Anvilfire.com, lesson number 139. I couldnt get links to work. Good luck! Keith

Looking good! What part of Missouri?

Put the the torch tip through the side, closer to the front door than center, and angle it towards the back, to induce swirl. Light it, close the door and wait for the exterior of your box to come to bright orange, then it's ready to open the door and start forging. Hope that handle ain't hot!!!!!!!!!!!!!!!! Then you can bare your teeth and spit in everybody's eyes!

thanks, having sticky goo on your metal all the time is incredibly anoying! Sounds like you rushing things and trying to forge with green coal instead of coking it up. Go to Blueprints and read up on fire control. Keith

Farriers anvils have a larger and flatter horn, and a narrower waist, less mass in the center of the anvil. But they are fine for a one person general shop. They just aren't made for a striker to hit with a sledge hammer. The 125# Cliff Caroll should have turning cams on the side, which are real handy for scroll work. I would buy it. Keith

Use the chops saw you bought at the farm supply, cut the wedge, squarely 1" longer than you want the height above anvil, ( about 2" so cut three )Now the harder part, move up 1" from the bottom and cut in from all 4 sides the amount it takes to leave the size hardy post you want, ( don't have to worry too much about over cut ). Now clamp in some type of vise and cut your square out from bottom up. BE CAREFUL.

Mine leak, but only for about a week after I fill them up. Suprisingly they dry and shrink within a couple days of being emptied. Fix: Empty it, turn upside down and tap around staves, not bottom boards, with a rubber mallet, right it and fill again. How old was yours when you bought it. I have a cooperage in town so mine was new and had minimal srinkage, when I bought it.

I googled, Catalan Furnace, this was the first of 60,000 hits. Metalworking Furnaces - San Juan Capistrano, California - Engineering Landmarks on Waymarking.com

It's beautiful. The drywall screws just take a little away. (very little)

Glad you weren't hurt! I had a "new" grinding wheel years ago, and since then, whenever changing wheels on ANYTHING, 4", 6", 8", bench grinders, angle grinders, cut-off saws, get out of the line of the wheel and run them free for ONE FULL MINUTE, and this does not guarantee anything, but it helps. People also have a tendancy to pick up tools, drop them, not say a word and put them back as found, I have came back from restroom, etc., picked up an angle grinder, ( that I was using a minute ago ) switched it on and had the wheel break immediatly. SAFTEY IS HARD WORK, BUT WORTH IT. Keith

Mount'neer, I would have balked, just like you, on having the dealers friend come up to price the vise. ( Don't like being conned ) I actually paid $105.00 for a 4" post vice, at a farm auction, here in southeast Missouri. It's in good shape and less than 1/2 of new. Keith

Hi Tim; Form pins are made of mild steel, and as such would be great to practice with. Try long tapers, making the round ones square, straight and the same size the entire length. When I started out I thought this was rediculous, but when I found out I couldn't do it, I started practicing. You will gain hammer control, and laern to flip stock 180 & 90 degrees. Work on projects at the same time so you don't get bored, but practice a little bit every day.

Again someone who doesn't want us to know where he lives. If he were my neighbor, and I knew it, I would invite him over to make a new one or redo the old one. I wonder if they are all "wanted", or in the witness protection program.

My post vice, a 65 lb. 4", no name on it, is in good shape per say, screw, pivot pin, jaws are flat and smooth, the jaws are only perpendicular at 1" open, this is by design, they are made to hammer on, not known for holding power, you must build jigs or tools to hold some material in the vice to keep it from moving. I can put a 3/8" bar in one side of the jaw and tighten till the vice flexes enough for the other side of the jaw to touch, and when released it will spring back to paralell. I use mine for holding some hardy tools, drifting or punching when my pritchel or hardy holes aren't big enough. I also have a saddle made to close on R.R. spikes to keep them from being driven down through the jaws when punching in faces etc. on trolls/wizards, without having to chase it around the anvil. There are blueprints for vise tools.

What works for you, works for you. there is no right or wrong, (boy I'm gonna catch-it for that), unless it comes to saftey. That said you are probably 1) using a cold chisel, slitting chisels are really thin, 1/16", and sharp, and hard, 2) hitting too hard on the first swing, just mark the cut line with the slitter, with the first heat, then hit a little harder with the second, and third and.......... I like you (it sounds) work alone, and traditionally that was not the case, there was someone there to hold, or strike things. The reason to learn traditional methods, is for demo's in front of the public.