Daswulf Posted September 19, 2015 Share Posted September 19, 2015 my brother often heads to some auctions I can't make it to and picked these guys up for me. The hardy is 1 1/2" so no good in my little hardy hole on my anvil but would work in a vice. I can tell oval shaped one in the lower right is for scrolling/bending. The other two have me baffled as to what they would really be intended for. The large one would make a nice small anvil top for in a vice but at the moment I don't see a need for it as that. I have absolutely no ideas on the little one up top. Anyone have any repurposing ideas or what I could use them for? Either way it's just some stuff I'll keep hanging on to till a purpose fits them. Quote Link to comment Share on other sites More sharing options...
ThomasPowers Posted September 19, 2015 Share Posted September 19, 2015 (edited) Did you meant the hardy stems or shanks are 1.5" square? I don't see a hardy in that lot of hardy tools.As to their original purpose---someone thought their job would be easier with them but I don't know what it was. Edited September 19, 2015 by ThomasPowers Quote Link to comment Share on other sites More sharing options...
Charlotte Posted September 19, 2015 Share Posted September 19, 2015 At that size they look like fixtures used in a vise. Quote Link to comment Share on other sites More sharing options...
Daswulf Posted September 19, 2015 Author Share Posted September 19, 2015 sorry i meant the stems (part that would be held by vice i guess) are 1 1/2" . thought it would be a bit large for a hardy hole on most any anvil. just trying to describe them as the looked. I still have alot to learn and i was wrong in thinking just because it has a stem for holding like that it would be considered a hardy tool. As to their original purpose---someone thought their job would be easier with them but I don't know what it was.and the obvious truth. We have an entire section devoted to tools, since it appears your busy schedule has prevented you from looking through the IFI forum to notice, I will relocate it for you. Quote Link to comment Share on other sites More sharing options...
ThomasPowers Posted September 19, 2015 Share Posted September 19, 2015 Yes they are hardy tools but not hardies which is a specific type of hardy tooling. Hardies are designed for cutting steel, thin profile ones for hot steel and thick profile ones for cutting cold steel. Not lumping all hardy tooling together makes it a lot easier when you say "hand me that hardy" and don't want any of the other pile of twisting forks, bridges, cones, bics, clip benders, fullers, bottom swages,... I have 3 anvils with a total of 4 1.5" hardy holes in them, (one has two). I generally have to make my hardy tooling from top tools that I forge the hammer eye section to fit using my screw press. I have also made a set of hardy hole sleeves to be able to use my "regular" hardy tooling with my large anvils. On my anvil with two 1.5" hardy holes I keep one sleeved for 1" and leave the other at 1.5" Quote Link to comment Share on other sites More sharing options...
DSW Posted September 19, 2015 Share Posted September 19, 2015 The long thin one and the oval one both look like the shank was welded on. It's possible the shape has little to do with the actual use. They may have simply been a piece of stock big enough to do the job, so it was used even if it was over sized or odd shaped ( oval). No real way to tell 100%. Quote Link to comment Share on other sites More sharing options...
Daswulf Posted September 19, 2015 Author Share Posted September 19, 2015 Thank you for clearing it up for me. As others have said there is a lot of info on the Internet and a lot of it can be generalized or just partial info. Those are probably pretty large anvils. I also thought about it and am thinking it would be hard to guess a repurposing for these without knowing what I'd be doing. I'd settle for any ideas tho. there are things to be learned through everything. Quote Link to comment Share on other sites More sharing options...
Alan Evans Posted September 19, 2015 Share Posted September 19, 2015 (edited) The long thin one and the oval one both look like the shank was welded on. It's possible the shape has little to do with the actual use. They may have simply been a piece of stock big enough to do the job, so it was used even if it was over sized or odd shaped ( oval). No real way to tell 100%.Funnily enough I came to the opposite conclusion sort of...It was the oval one which is the only thing I thought I had a clue on, and it was that it was a specific shape to wrap a link or loop around. The lug on the long side of the oval appears to be a hook to hold the end of the workpiece when you start to pull it around. As far as the hole in the middle goes I have made up similar jigs which also have provision to hook the end pin of a scroll wrench/bending fork in so you can pull the bar tight to the profile. Though I normally put the pin hole in the centre point of the arc.Alan Edited September 19, 2015 by Alan Evans Quote Link to comment Share on other sites More sharing options...
Daswulf Posted September 19, 2015 Author Share Posted September 19, 2015 The lug on the long side of the oval appears to be a hook to hold the end of the workpiece when you start to pull it around. that is what that appears to be. Quote Link to comment Share on other sites More sharing options...
DSW Posted September 19, 2015 Share Posted September 19, 2015 Ok that makes sense now as far as the oval for doing chain links. I hadn't thought of the center hole as a pivot for a wiper bar to help with wrapping the link. Quote Link to comment Share on other sites More sharing options...
Dogsoldat Posted September 19, 2015 Share Posted September 19, 2015 could the top right hand one be for forming collars? Quote Link to comment Share on other sites More sharing options...
Everything Mac Posted September 19, 2015 Share Posted September 19, 2015 That one on the top right could be for forming collars as Dog says, - it would also be good for forming box jaw tongs... Andy Quote Link to comment Share on other sites More sharing options...
Daswulf Posted September 19, 2015 Author Share Posted September 19, 2015 Those are good ideas on that one. I really had no clue other then they look like the one half of box jaw tongs. Thank you for the ideas. i never would have thought of collars. Never know, thats why it's nice to get others opinions, guesses, ideas. On the longer piece, i had some ideas on uses but i'd hate to modify such a nice large piece only to find a better use for it later(has happened) when i could have made a simpler, smaller, solution earlier off. Quote Link to comment Share on other sites More sharing options...
ThomasPowers Posted September 20, 2015 Share Posted September 20, 2015 The anvils are not very large: 515# Fisher, 410# Trenton and a Bridge Anvil from the oil patch. Remember Anvil Envy can be an expensive vice. (Vise envy is an expensive vice too) Quote Link to comment Share on other sites More sharing options...
Daswulf Posted September 20, 2015 Author Share Posted September 20, 2015 haha i'm not very envious, but a larger anvill then a 100# would be nice. i'm in no hurry tho. and i like the post vices i have so far. no big deal at least i have pretty good stuff i scrounged to start with. i'm happy so far tho i do want to improve my skills And equipment. skills/ knowledge are first. Quote Link to comment Share on other sites More sharing options...
ThomasPowers Posted September 20, 2015 Share Posted September 20, 2015 Currently I have many more hours on my 91# arm and hammer than my 515# fisher. As it's my travel anvil and when I demo I get to use it all day long compared to the rare times I get to use my shop now. Quote Link to comment Share on other sites More sharing options...
Daswulf Posted September 20, 2015 Author Share Posted September 20, 2015 Even with the big boys, you use what work for the job. That's a good lesson. Quote Link to comment Share on other sites More sharing options...
Frosty Posted September 20, 2015 Share Posted September 20, 2015 My go to anvil is a 125lb. Soderfors and it's but one step from my 206lb Trenton. I've never noticed the extra 81lbs. making much difference other than using bending forks.Frosty The Lucky. Quote Link to comment Share on other sites More sharing options...
Daswulf Posted September 20, 2015 Author Share Posted September 20, 2015 i do notice mine moves around on me a bit but it dosnt affect my work, just means i need a heavier base or to bolt it down but i dont have my area set up how i want it yet to bolt anything down. no biggy, I can always nudge the stand back where it belongs for now. hey i'm just starting out. i need the exercise and again it's not the size of the anvil, it's how you use it. for now, for me i'm happy with what i got. and with these hardy tools, i'll find a use for them eventually or pass them on to the next person that has an idea for em. Quote Link to comment Share on other sites More sharing options...
matto Posted September 20, 2015 Share Posted September 20, 2015 thomas i would disagree with you that hardies are "only" cutting tools that go in the hardy hole of an anvil. All tooling that go in the hardy hole are hardies. We have just come custom to calling our hot or cold cut hardies "hardies. it is like calling all locking pliers "ViseGrips" or all ajustable end wrenches "Crestent wrenches" or calling a box end wrench a wrench, but you also have combination wrenches, open end wenches, flare nut wrenches, pipe wrenches ect... all can be called wrenches. Quote Link to comment Share on other sites More sharing options...
Frosty Posted September 20, 2015 Share Posted September 20, 2015 thomas i would disagree with you that hardies are "only" cutting tools that go in the hardy hole of an anvil. All tooling that go in the hardy hole are hardies. We have just come custom to calling our hot or cold cut hardies "hardies. it is like calling all locking pliers "ViseGrips" or all ajustable end wrenches "Crestent wrenches" or calling a box end wrench a wrench, but you also have combination wrenches, open end wenches, flare nut wrenches, pipe wrenches ect... all can be called wrenches. Nope you have it backwards. The hardy hole was introduced into anvils to hold the already existing Hardy which is a cut off chisel used edge up. There may be various shapes of hardy, hot, cold, curved, butcher but all are cut off chisels. Probably the closest modern cut off to the original "hardy" is an "anvil devil." Basically a cut off chisel with a base wide enough to lay on the anvil face and be stable enough to do the job. I imagine the modern anvil devil is changed significantly from the olden day's hardy.The oldest reference I've seen to bottom tools for the hardy hole are as "shank" bottom tools.Calling anything with a square shank a "hardy" is a modern corruption of the terminology.Frosty The Lucky. Quote Link to comment Share on other sites More sharing options...
Daswulf Posted September 21, 2015 Author Share Posted September 21, 2015 i'm in no position to argue the point. so i'd have to let you guys argue the point. Quote Link to comment Share on other sites More sharing options...
ThomasPowers Posted September 21, 2015 Share Posted September 21, 2015 I'll see if I have time to look over Moxon tonight. Quote Link to comment Share on other sites More sharing options...
Everything Mac Posted September 21, 2015 Share Posted September 21, 2015 I'm not sure I agree with a cut of hardy simply being called a "hardy" - I'm sure the forum at large went through a phase of calling a cut off tool a "Hot cut" But as much as I love a good discussion over semantics, I much prefer talking about tools. What are you going to do with them Daswulf? Andy Quote Link to comment Share on other sites More sharing options...
Daswulf Posted September 22, 2015 Author Share Posted September 22, 2015 the oval one i'll give a shot at a bending tool. the oblong one i might use as a more crisp anvil face as needed until i find a better use. and the other i dunno. maybe give them a shot at helping with box jaw tongs when i try a set, or collars when i'm ready. what ever they speak to me as. or if they could help out someone who has a purpose. I really like hearing what peoples ideas are on things i'm not sure of. it gives me ideas if not someone saying hey! i've been looking for That thing. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.