-
Posts
61 -
Joined
-
Last visited
Content Type
Profiles
Forums
Articles
Gallery
Downloads
Events
Everything posted by eriktlupus
-
It takes money to blacksmith !!!!
eriktlupus replied to rthibeau's topic in Blacksmithing, General Discussion
I remember the same discussions when I was brewing beer regularly. As in how do you consider the costs of your time to brew the beer versus what you would otherwise be doing? The answer was usually since it was a hobby for most of us(just as it is here) the time 8s not taken into account when telling that it costs you this much per beer. The start up costs to do beer are actually greater than blacksmithing. -
Thomas That is just cruel. Hilarious but cruel.
-
Show me your blacksmith pets
eriktlupus replied to Glenn's topic in Blacksmithing, General Discussion
My money is on Herman. -
help construction digging homemade bar
eriktlupus replied to angiolino's topic in Blacksmithing, General Discussion
The one I use is 6ft of 1inch stock. Upset into a mushroom cap for the hand end and a squared chisel tip on the business end. -
We've used such weights a drag anchor to slow the boat down when fishing the river. Tie a short length of chain to the anchor line and the use a carabiner to attach the sash weight. Keeps the rope from being worn by the stones and rocks.
-
My workshop and a knifemaking course
eriktlupus replied to BartW's topic in Blacksmithing, General Discussion
Heck just put blacksmith classes into the search bar. I found 15 different places on the 1st page. Now granted they might not be local to me(or you) but they are out there. I went thru tillers international since they are local to me. $200 for the weekend class ( 2 days lunch provided). Took it with my dad also. -
When I was brewing beer I would have the tanks freezing up while doing the boil on a banjo burner(sounds like a jet engine when running full bore). The solution for us was to take the spent grains (@140f) and bag em in a garbage bag and set the tank on the bag during the boil.
-
Another source of the problem might be mixing in commercial briquettes. The binders they use when forming will inhibit forge welding iirc.
-
I'm a factory rat (we make radiators and evaporators) temps in the shop regularly reach well into the 100's with a very high humidity (Michigan). One of my coworkers this past summer went down with heat stroke from not drinking enough, took 4 iv's in the hospital and 4wks before he was able to return to work. The company I work for supplies Gatorade and extra breaks when the temps inside reach a feels like of 90.
-
Show me your blacksmith pets
eriktlupus replied to Glenn's topic in Blacksmithing, General Discussion
Killbox, love the twin pic. Makes me want to go out get another retriever. Probably gonna wait a few more years till my lowrider lab passes. Hmm can't find a pic on the new phone. -
What weird animals have been in your shop
eriktlupus replied to Glenn's topic in Blacksmithing, General Discussion
Not truly in my shop, have a few whitetail does that forage in the raspberry plot that is next to it. Did have a herd of turkeys that would hang around the same area but haven't seen them the last couple years since the coyote population picked up. -
So looking like a 2:1 ratio of water and silica. Thank you. I read the entire forges 101 thread and either didnt see it or was just so flooded with info i forgot it
-
I have been going thru the the forges 101 thread and using search ( rigidizer formula+iforge iron) but i cannot seem to find a ratio of water to powder to use when spaying the blanket down. Is this a hard science or is it just an experience type thing? Any help is greatly appreciated. Erik
-
The car blower works fine. Just need to have a way to reduce volume. Either by rheostat, gate valve or a gap between the blower and the tuyere. Dont forget an on/off switch. I use an old deep cycle battery for a trolling motor that will last an easy 10hrs before i need to recharge it. A newer one will likely last much longer since the blowers draw is much less than a trolling motor.
-
Coal at local Tractor Supply
eriktlupus replied to Technician.Austin's topic in Solid Fuels: Coal, Coke, Charcoal, Wood, etc
I use this type of coal in about a shelled walnut size. Light it with a charcoal fire and it definitely likes to be well aerated. I have a blower that throws sparklers with lump but this coal loves it -
Thor. Some cities prohibit any outdoor burning without permits including the enclosed chimneas that are so popular.
-
i haate you zombie....so what if the blower is frozen you still stole it at $40. Wish mine had cool stuff like that
-
Stoopid forbidden 18 assorted files and a 3lb xpien for $20
-
smelting questions
eriktlupus replied to eriktlupus's topic in Smelting, Melting, Foundry, and Casting
Thank you daniel and jammer. More info is always appreciated. Charles...i knew there had to be something historically since steel was so scarce they had to have a way consolidate all the small scraps in the shop scale, filings etc. Charlotte.. always try to be safe. Burned myself too much growing up not to -
smelting questions
eriktlupus replied to eriktlupus's topic in Smelting, Melting, Foundry, and Casting
Steve i also never said anything about pouring. Asking if i could use the mix in a smelter or for a crucible steel. Turns out I'm not the only one to think of this. after looking around online i found a practice called orishigane (oroshigane) which is a practice for increasing the carbon content of steel or using shop scraps to form new steel. Using a small bloomery style furnace that is not smelting -
How do you get the bolster to form from the knife material? Is it an upset or a leftover from original size?
-
I have a bucket of this type as well. Not sure if it will work kwool though since it is a thick mortar for joining fire brick together rather than a wash as itc-100 is. I was gonna use it to coat a hard cast refractory.
-
US propane is listed as fil or flare fittings
-
Look for "man at arms: reforged" and check out them doing the LOTR sword Narsil they do the whole video without grinders. They do use a power hammer from the late 19th though