Ross_FL Posted October 27, 2010 Share Posted October 27, 2010 HF has a belt grinder for $75, it looks like this HF grinder I'm guessing it's garbage, but does anyone happen to have experience with this model? Quote Link to comment Share on other sites More sharing options...
Mainely,Bob Posted October 28, 2010 Share Posted October 28, 2010 Especially in this case you get what you pay for.The fitting that allows the belt to be swiveled on these is made of low grade cast iron and breaks easily.I have been asked to repair 3 of them and told the people who brought them in it was a waste of time as the rest of the machine was of equally low quality. My suggestion would be to look on Craig`s list for an older,better made machine.One that is built to stand up to metalwork rather than a woodworking machine.They can be bought relatively cheaply nowadays. Quote Link to comment Share on other sites More sharing options...
arftist Posted October 28, 2010 Share Posted October 28, 2010 I bought this http://www.kalamazooind.com/products/belt-sanders/s4s-belt-sander/ used for $100 off craigslist. I had to drive over an hour to get it, but I will always have this tool. I also bought this http://www.kalamazooind.com/products/belt-sanders/s6ms-6%E2%80%B3-belt-sander/ used off craigslist for $100. It was a couple towns over and cost four times as much as the smaller one new. They are both great sanders and were both great deals. Quote Link to comment Share on other sites More sharing options...
Ross_FL Posted October 28, 2010 Author Share Posted October 28, 2010 Especially in this case you get what you pay for.The fitting that allows the belt to be swiveled on these is made of low grade cast iron and breaks easily.I have been asked to repair 3 of them and told the people who brought them in it was a waste of time as the rest of the machine was of equally low quality. My suggestion would be to look on Craig`s list for an older,better made machine.One that is built to stand up to metalwork rather than a woodworking machine.They can be bought relatively cheaply nowadays. Thanks Bob, HF scratched off the list. I bought a heat gun there that worked for 15 minutes and its that same orange color as the grinder so I was wondering if it was the same cheap crap. Then again, the heat gun was $3, so that's about one use worth!! Quote Link to comment Share on other sites More sharing options...
R.Harrell Posted October 28, 2010 Share Posted October 28, 2010 Hey I bought a 1" x 30" belt sander from HF and it gets the job done for light sanding. I bought some leather belts and do some sharpening on it too. Here is a picture of the sander on the site. My link It was only about $40.00 from my local HF bought as the other said you get what you pay for. I would love to build that "no weld" belt grinder that they sell plans for. Quote Link to comment Share on other sites More sharing options...
the hangman Posted October 28, 2010 Share Posted October 28, 2010 Hey I bought a 1" x 30" belt sander from HF and it gets the job done for light sanding. I bought some leather belts and do some sharpening on it too. Here is a picture of the sander on the site. My link It was only about $40.00 from my local HF bought as the other said you get what you pay for. I would love to build that "no weld" belt grinder that they sell plans for. R.Harrell: I have one of those HF 1"x30" belt sanders also. One of my other hobbies is building and flying remote-controlled airplanes and helicopters. That little sander is great for small work. I burned up my first one after a couple years and my second one is starting to go . . . I would like to find a similar unit - but made a little better Jeff Quote Link to comment Share on other sites More sharing options...
Marksnagel Posted October 29, 2010 Share Posted October 29, 2010 I'm also looking for a combo sander. I am willing to wait until I have the cash rather than buy a piece of trash. Thanks Bob for the input. I'll steer clear of HF. Mark<>< Quote Link to comment Share on other sites More sharing options...
bigfootnampa Posted October 29, 2010 Share Posted October 29, 2010 Here's a link to some 2" belt grinders that are very basic but also not too expensive. I've been thinking on one of these for a while.hurricane grinders They seem reasonably well built and have continuous duty motors. I haven't tried one yet though. Quote Link to comment Share on other sites More sharing options...
Marcus Hopfinger Posted October 29, 2010 Share Posted October 29, 2010 Here is another option as well. The gentleman that sells these is an IFI member. Quote Link to comment Share on other sites More sharing options...
Ross_FL Posted October 29, 2010 Author Share Posted October 29, 2010 Here is another option as well. The gentleman that sells these is an IFI member. $800 and I gotta build I myself?? Uhhh, thanks, I guess. Quote Link to comment Share on other sites More sharing options...
Marcus Hopfinger Posted October 29, 2010 Share Posted October 29, 2010 $800 and I gotta build I myself?? Uhhh, thanks, I guess. Sorry, I guess I didn't look at the prices. Just knew he sold grinder kits so I posted the link quickly. Quote Link to comment Share on other sites More sharing options...
Rich Hale Posted October 29, 2010 Share Posted October 29, 2010 One thing I do not see covered in this thread is simply wot is the belt grinder going to be expected to do? The Hf grinder can do a few things that are not above its capabilities. Other grinders will do those and a long list of other things a lot better. One grinder I keep in the knife shop is a grizzly 2"x72" I do lots of work on it and have for a lot of years. Kind of a general purpose utility grinder. I use a Hard Core grinder for knife work and almost everyone of them is hollow ground and full tang knives have tapered tangs. That size belt is availeable in a long list of different grits and qualities to do anything I want to do on my knives. A few things I would not be without for knife work is a flat platen, a rubber covered contact wheel,,(I prefer an 8") And a small wheel attachemant. I have 1/2", 5/8". 3/4",1" and 1 1/2" wheels for that. A huge must have item is a way of controlling the speed. I like the variable speed motors. But if I had to I would be fine with a system of pulleys that I could move belt for different speeds. Quote Link to comment Share on other sites More sharing options...
bigfootnampa Posted October 29, 2010 Share Posted October 29, 2010 I saw a "variable frequency" 2" belt grinder on Craig's list today. Anyone familiar with these? It was NOT cheap... they are asking $2,000 for it. Seems it must be something special. Quote Link to comment Share on other sites More sharing options...
bigfootnampa Posted October 29, 2010 Share Posted October 29, 2010 BTW the polar bear forge kit is only $250 but he has projected it based on other parts that you'd buy separately to cost around $780. Since some grinders with similar features are in the 2k to 4k range it is not exactly highway robbery what he is asking for these. Quote Link to comment Share on other sites More sharing options...
pkrankow Posted October 29, 2010 Share Posted October 29, 2010 $800 and I gotta build I myself?? Uhhh, thanks, I guess. That polar bear kit can be compared to some commercial units, so it is a little easier to swallow...I still can't. I have an old Mead Bandsander (they show up on Ebay too, go cheap sometimes) and I am happy with it. It is a 1x42, I have a 1/6 hp motor on it, and it is nice but underpowered. It calls for 1/3 to 1/2 horse. The motor is separate, but I see no need to upgrade the motor at this time, it works great! Phil Quote Link to comment Share on other sites More sharing options...
maddog Posted October 29, 2010 Share Posted October 29, 2010 At a glance, that looks like a nice grinder kit. And for the work he puts into it, the price is cheap. I assume the motor is not included. But it seems over engineered. Is 1/2" plate really necessary? And is it worth the extra effort to be able to change belt sizes? Also a welded fabricated construction would be both stronger and a lot cheaper. Quote Link to comment Share on other sites More sharing options...
eric sprado Posted October 30, 2010 Share Posted October 30, 2010 The little HF 1" belt grinder for around 35 bucks is a DREAM for sharpening. You need to buy belts somewhere else. With a fine grit belt I sharpen everything. Had it for two years now.... Quote Link to comment Share on other sites More sharing options...
Ernst Becker Posted May 18, 2011 Share Posted May 18, 2011 All Hands: I need a bit of advice. I'm new to knife makin. My question, what is an efficient knife grinder? I know I'll have to pay. I like some advise as to which one would be a dependable buy? Semper Fi, Ernst Becker Quote Link to comment Share on other sites More sharing options...
Dodge Posted May 18, 2011 Share Posted May 18, 2011 All Hands: I need a bit of advice. I'm new to knife makin. My question, what is an efficient knife grinder? I know I'll have to pay. I like some advise as to which one would be a dependable buy? Semper Fi, Ernst Becker Oorah Ernst. KMG seems to the the top of the wish list of grinders but there are clones out there. Bader is another fine tool. Either will run a grand or so for a new one.... Quote Link to comment Share on other sites More sharing options...
ianinsa Posted May 18, 2011 Share Posted May 18, 2011 Let's get real here guys! on one hand you are talking $40.00 sander and on the other (the polar bear job) something your grandchildren will still use!(though I balk at the price). It's like compairing house brand grapejuice to Chateau d'Yquem 1980. The H/F job( $40) looks to be what it is a small cheap and cheerfull(maybe more cheap than cheerfull)probably ideal for regular re-sharpening. But I must agree with the sugestions on buying a older second(or 3rd/4th)hand industrial use tool. Ian Quote Link to comment Share on other sites More sharing options...
nuge Posted May 18, 2011 Share Posted May 18, 2011 The thing I learned about belt grinders is that I use them alot. More than I like to admit given my aversion to grinding. I don't make knives and I sprung for a KMG and don't regret it at all. The unit is HEAVY which is real nice in a grinder but I sure don't like moving the machine. If you have more time than $ the Beaumont Metalworks website is set up so you can buy the necessary bits and build the machine yourself, plans are around. And they answer the phone. The HF unit looks good for sharpening but you probably wont be removing much material. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.