Mark Aspery Posted February 7, 2009 Share Posted February 7, 2009 What is the difference between a heading plate & a bolster I have used the terms interchangeably throughout my career as a smith. I think that -'Wind direction during use'- is probably the single most important factor determining the use of one name over another that I have seen. Does anyone have a definitive definition? Quote Link to comment Share on other sites More sharing options...
divermike Posted February 7, 2009 Share Posted February 7, 2009 I'm no expert, but my guess is that the bolster, based on definition, is to support or hold, and the header, while also being useful for this, is a tool specific to it's name. Quote Link to comment Share on other sites More sharing options...
nett Posted February 7, 2009 Share Posted February 7, 2009 Mark, I'm only guessing and I know I'll be corrected. A bolster plate is inclusive; it can be used for heading material and shaping material along it's length. A heading plate exclusively addresses the end, the head, of the stock. Quote Link to comment Share on other sites More sharing options...
HWooldridge Posted February 7, 2009 Share Posted February 7, 2009 FWIW, this is my personal definition: A bolster is any sort of support under work. In the blacksmithing world, it could be a piece of material bent into a "U" which is put under hot work to support a drifting operation. OTOH, a heading tool has a defined internal dimension (but not required to be round) to support a specific heading operation. Quote Link to comment Share on other sites More sharing options...
rthibeau Posted February 7, 2009 Share Posted February 7, 2009 Mark...I would make a post, but if you don't know, we ain't gonna and that's for sure Quote Link to comment Share on other sites More sharing options...
Mark Aspery Posted February 7, 2009 Author Share Posted February 7, 2009 (edited) I agree with the opinions stated. I think Nett's is closest to my own opinion. But it's just that, an opinion. I was really looking for chapter and verse. Even in older text I cannot find a definition. A heading plate to me was/is a flat surface with a hole in it. A bolster is anything other than a flat surface with a hole in it. In the photos attached I am drifting over two different plates. In fact one was used to make the other (as shown in photo). I know what I WANT to call each piece, but I cannot find anything that offers a definition. Edited February 7, 2009 by Mark Aspery Spullin Quote Link to comment Share on other sites More sharing options...
Paul B Posted February 7, 2009 Share Posted February 7, 2009 Well I will put in my two cents. In a power press, mechanical or hydraulic, a bolster is the upper and lower plate that the die shoes bolt to. I don't know if this has any bearing on the discussion. Quote Link to comment Share on other sites More sharing options...
Grant Posted February 7, 2009 Share Posted February 7, 2009 I believe this restates Hollis's definition. Header; One who, or that which, heads nails, rivets, etc., esp. a machine for heading. Bolster; To support, hold up, or maintain with difficulty or unusual effort; -- often with up. A Header is a special case of bolster - supporting the heading operation. In this case it is the use of the support that defines the tool. Mark, both of your supports are bolsters as they are shown in use. grant Quote Link to comment Share on other sites More sharing options...
devon blacksmith Posted February 7, 2009 Share Posted February 7, 2009 I would use a bolster for suporting whilst punching and a header to head bolts and rivets the header is a lot smaller than the bolster as you need to angle the blows to form the head ,if you used the wide flat plate of a bolster desined to suport the punched piece you could not form a good shape of head. Quote Link to comment Share on other sites More sharing options...
Mark Aspery Posted February 7, 2009 Author Share Posted February 7, 2009 . I would still be inclined to follow the lead of Mr. Lillico and call them bolster and swage bolster Of course, I could be wrong, flipping through some books and quoting them doesn't make one right :-) Thanks Gerald, I've followed Lillico for a long time now - I see no reason to abandon his council at this stage! Good research - thank you. Can you give me chapter and verse (page and paragraph) please. Thanks to all who have contributed. Quote Link to comment Share on other sites More sharing options...
TASMITH Posted February 7, 2009 Share Posted February 7, 2009 In my experience in industrial Blacksmithing a Bolster was used to support material in some matter, such as bolster blocks in a power hammer which supported and anchored the various hammer dies, or in the use of a 'Header' machine. In the header machine the bolster clamped the material in place and a 'Header" struck the protruding end of the bar and formed the head shape. This is the same type of machine used to form button head rivits or hex head bolts etc. Terry Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.