JME Posted November 26, 2016 Author Share Posted November 26, 2016 Metal mangler Time is very valuable, right now my time in the forge is mostly spent learning. I love the idea of making something out of scrap but I dont think I will use it for tools unless I know what it is. The rebar was a good experiment, it was hard to move the metal and the tongs work but not sure I trust them all that much. Live and learn, that is what it is all about. Jme Quote Link to comment Share on other sites More sharing options...
Frosty Posted November 26, 2016 Share Posted November 26, 2016 I Agree with Metalmangler and have a couple bits to add to the opinion. Using known steel for any project removes the often unexpected working characteristics from the project. Learning to blacksmith is a large and never ending learning curve, using a known material removes a whole different craft from the learning process. Once a person has become proficient working the metal learning to identify a mystery metal's working properties is much easier and you can concentrate on that learning curve. As Mark says your time is the one thing you bring to the game and is limited. Spending it wisely is a good thing. Frosty The Lucky. Quote Link to comment Share on other sites More sharing options...
metalmangeler Posted November 27, 2016 Share Posted November 27, 2016 JME I hope I did not come across as negative regarding your tongs, you jumped in and made tongs...... this is great and no doubt you will get better if you keep it up. You are light years ahead of the people who never start because they might not do it perfect. I have some light tongs I made from 3/8 round i know over 16 years ago they are still going strong. I don't use that steel now but it obviously worked. I hope my comments were seen as helpful not critical that is my intent, sometimes hard to know on the internet. Quote Link to comment Share on other sites More sharing options...
JME Posted November 27, 2016 Author Share Posted November 27, 2016 7 hours ago, metalmangeler said: JME I hope I did not come across as negative regarding your tongs, you jumped in and made tongs...... this is great and no doubt you will get better if you keep it up. You are light years ahead of the people who never start because they might not do it perfect. I have some light tongs I made from 3/8 round i know over 16 years ago they are still going strong. I don't use that steel now but it obviously worked. I hope my comments were seen as helpful not critical that is my intent, sometimes hard to know on the internet. I like the comments. I have never been afraid of jumping in and trying something new. Learning the process has been great so far. I dont know about anyone else but I need to have hands on and make some mistakes so I can get better. I am trying to make some knifes. (eventually want to make some kitchen knives) this is my latest endeavor. This is a practice blade. Deer antler handle and lawnmower blade. I will eventually be making the blades with stainless but this is good practice for now. Once I make a few dozen knives with different handles I can attempt the kitchen set. JME Quote Link to comment Share on other sites More sharing options...
Francis Trez Cole Posted December 29, 2016 Share Posted December 29, 2016 take a few minuets every time you light the forge and hammer out a jaw, boss and start of the reins. Make sure you do not make the boss to thin. In stead of flattening the boss out try slitting and drifting the hole. Remember the tong makers use 1045 steel Quote Link to comment Share on other sites More sharing options...
Iron Poet Posted December 29, 2016 Share Posted December 29, 2016 You should try to sand that knife, sanding and finishing is harder than most people suspect and it's better to learn those skills on practice piece instead of trying to learn on something yo can't mess up. Quote Link to comment Share on other sites More sharing options...
JME Posted January 2, 2017 Author Share Posted January 2, 2017 I am practicing my sanding. It is difficult to keep everything even and smooth but I am getting better. I had a productive afternoon. Made a tomahawk and a straight razor. Tomahawk turned out ok. Good for a first try anyway. It was made for a friend. He wanted something to make kindling. It should do fine and I learned lots. I need the practice. Next tomahawk is for my stepson. The razor was a lot of fun to make. I will be doing some more of these. I also earned that I should not rush things. I broke it marking with the punch for the pivot hole. Now it is in 2 pieces. Oh well, live and learn. Forge on and have fun. Happy New Year JME Quote Link to comment Share on other sites More sharing options...
Tubalcain2 Posted January 2, 2017 Share Posted January 2, 2017 not 2 bad fer a newbie. Quote Link to comment Share on other sites More sharing options...
C-1ToolSteel Posted January 3, 2017 Share Posted January 3, 2017 Good work. PS: I really like the hot cut you built into the RR track! Quote Link to comment Share on other sites More sharing options...
JME Posted January 3, 2017 Author Share Posted January 3, 2017 2 hours ago, Tubalcain2 said: not 2 bad fer a newbie. Thanks. I try 57 minutes ago, C-1ToolSteel said: Good work. PS: I really like the hot cut you built into the RR track! Thanks. I am thinking about a bottom fuller for the other side. Haven't decided yet. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.