-
Posts
349 -
Joined
-
Last visited
Content Type
Profiles
Forums
Articles
Gallery
Downloads
Events
Posts posted by Zeroclick
-
-
Welcome, sounds like your off to a great start. Can't wait to see some photos of your work.
-
-
12 hours ago, Daswulf said:
They sure look used from the photo. Sealed boxes? Sometimes techs toss the old parts in the box the new part comes in.
Still, great tool material.
I did think the same when I opened a few but they were all sealed, apparently just been stored for a very long time in some very bad conditions.
The one on the top was out of the scrap bin though.
-
-
Hi Phantom,
You might be able to use parkersteels for stock if they deliver to your area. I have heard a few good reports about them.
-
9 minutes ago, JHCC said:
Réaumur.
I had never heard of this before but just had a quick read and is an interesting concept.
-
Always use Kelvin its how real men measure temp.
-
No problem, it does look very nice i really like the twist.
-
You could do a hot vegetable oil finish for it. This will be food safe, and give it protection against rust.
-
-
-
My first forge was half of a 6x4 shed, with my forge just outside the door meant I could work small pieces and muffled some of the noise for my neighbours.
Now I am in a 20x10 workshop, with a good solid concrete floor to bolt my vice to. It has made such a difference as now I can work no matter the weather.
-
That is a very nice knife, I really like the look of that handle.
-
Welcome.
Always love to see pictures, do you have any photos or details on the anvils that will be available.
-
Thanks Smoggy.
I was curious as I had seen that the lower the speed could go the more suitable it was for metal to prevent drill bits burning out.
The tolerances isn't to much of an issue as I will be only using it on handmade items.
I might keep an eye out for a decent second hand one and if I don't find anything just wait for the next DIY sale they have.
-
I would love to get a proper industrial one that i know will just keep going but I know i won't have that kind of cash for a while.
I was just hoping to upgrade from the handheld setup and the 3 year warranty is a big selling point. I could have a look for a good quality second hand one bu need do more reading on what to check for.
-
Well I did think that but I then compared it to the Clarke Metalworker and the speeds seemed comparable if not slightly lower.
The Clarke's ranger was 620-2620.
I would be drilling Metal with it nothing more than 10mm as I would be using it for the mouting holes for hooks and the like anything thicker I would punch the hole through hot.
I am just not used to the spec for drills presses and seem to see them vary greatly between the machines.
Sorry for not providing greater detail in my original post.
-
Hi All,
I have seen this drill press for sale, and would like some advice on whether it is worth getting.
My current setup is I drill free hand or use a hand drill in a drill press but I have run into a few issues with this setup as my only way to kill the drill is to reach over and pull the plug.
Thanks,
Luke
-
-
The link below has a huge amount of data on the various flypresses and their specs.
-
Perhaps an upgrade in your PPE for a short time
-
16 hours ago, Chris Comtois said:
Got another load of used horseshoes from my source. Spent some time messing around with a few.
Nice hearts, and the pumpkins are really cool.
3 hours ago, Gergely said:Dear All,
Thank you for all the kind words, it helped a lot. I managed to get some things done in the workshop and of course I enjoyed it very much. I wanted to take pictures but in the middle of the afternoon I successfully applied a brand new 9" cutting disc at full speed on my left thigh. I got off with a minor wound - if we compare to what these grinders can cause to human flesh. Spent the rest of the evening in the ER. All this because I was stupid enough to not turn off the grinder, and remove a hanging piece of steel with hand. No, I wanted to proceed quickly. Now here is quick for me, isn't it?
Anyway, thank God I have so light surface wound that I can walk and stand without further problems or pain. The funniest thing was that in the ER they taped it together! I was worried if it got stiched or sew but modern times: strips of tape hold together the two parts
Bests to you!
Gergely
Good grief you seem to be having a bad time of it, wish I could come over and lend a hand.
Hope you heal quickly.
Best wishes,
Luke
-
That is really cool,
-
It's always nice when it happens.
Can you tell
in Blacksmithing, General Discussion
Posted
Hi Everyone,
So I was listening to the Blacksmith's Pub podcast, I think it was Episode 20 (but I am not a 100%) and the guest said he was teaching a class. With one guy attending and he said within 10 mins of forging he could tell that this guy was never going to be able to go professional.
This made me think is this really possible, and thought I would ask what people thought about the idea.
Cheers,
Luke