canada goose Posted May 25, 2016 Share Posted May 25, 2016 Would anyone on here like to describe their procedure for making the dog bone arms for a Clay Spencer tire hammer ? I am commencing a ( slow) build and have limited machine work experience so I need some pretty basic help. Quote Link to comment Share on other sites More sharing options...
setlab Posted May 25, 2016 Share Posted May 25, 2016 Dies this help? I'm in the process of building mine, I'll do a wip when I'm done. But here is my welding jig I made. Quote Link to comment Share on other sites More sharing options...
canada goose Posted May 27, 2016 Author Share Posted May 27, 2016 I like the jig you show. And the some of my uncertainties would apply to that pn 37 ,but the "dog bone " I refer to is the link weldment pn 211. It uses 1"x11/2"I sch80 pipe and an oilite bearing the same as pn37 .I presume the ends of the 11/2" pieces would be squared in the lathe before welding. But can the pipe ends be bored square to the sides after welding? The oilite bearings I find at MSC are .0753 inside .Is this 3 thou. a standard clearance for a 3/4 pin? The plans say to press bearing in and then ream to .750" . Shared insight appreciated. Quote Link to comment Share on other sites More sharing options...
WL smith Posted May 28, 2016 Share Posted May 28, 2016 I am not a hammer guy, however the important measurement at this point is the O D of the oilite bearing and the ID of the pipe. I don't have any books handy for schedule 80 pipe. Quote Link to comment Share on other sites More sharing options...
WL smith Posted May 28, 2016 Share Posted May 28, 2016 Sorry if I came across as harsh (I reread my post). Yes the directions are accurate get the bearing in the pipe then ream. Wish you well on the spencer. Quote Link to comment Share on other sites More sharing options...
setlab Posted May 29, 2016 Share Posted May 29, 2016 Unless you made a jig to weld the inside diameter perpendicular to the dog bone arm squaring the end of the pipe up before welding would be the best way to keep it square. You make the PN 37 and dog bone weldment basically the same, couldn't find a picture of my dog bone. As for the bearings I don't know much about that, I've just been following the plans pretty closely on the movable parts. Once I drilled and reamed the dog bone pressing in the bearing was simple, I was surprised at how little material was removed when I reamed the bearings to .75 on a drill press. I squared the pipe on a mini mill with a long cutter and I did everything else on the drill press. Quote Link to comment Share on other sites More sharing options...
canada goose Posted May 30, 2016 Author Share Posted May 30, 2016 so you used a drill bit to bore the sched 80 from .936 to ? and then 1 " reamer ? Does a 1" bearing press into a 1'' Hole ? Quote Link to comment Share on other sites More sharing options...
setlab Posted May 30, 2016 Share Posted May 30, 2016 Yes, I'd have to look at what size I used though. Google will tell you better than I. I searched around ebay and found a decent priced morse taper drill to do the job. Quote Link to comment Share on other sites More sharing options...
FieryFurnace Posted June 1, 2016 Share Posted June 1, 2016 I used a 1-inch holesaw to ream the pipe out to final size after I assembled the arm. Then used my post vise as a press to push the oilite bearing into the pipe. It's tight, but it does fit. I have no milling equipment so I used a drill press for the drilling, a bandsaw for cutting, and a belt grinder for cleaning up the ends. If you have access to milling equipment, that's great.....if not, it isn't the end of the world. Close does work. Quote Link to comment Share on other sites More sharing options...
punkinracer Posted June 1, 2016 Share Posted June 1, 2016 I went the easy route and machined then out of solid on my CNC Mill. I suppose that is cheating a bit! Quote Link to comment Share on other sites More sharing options...
canada goose Posted June 1, 2016 Author Share Posted June 1, 2016 Well I have no milling machine access but can use a friends lathe for squaring the ends of the pipe. F.furn why did you choose to use a hole saw rather than a drill bit? After pressing the bearing in did the pins fit properly or require reaming ? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.