DIDTAS
Members-
Posts
34 -
Joined
-
Last visited
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
-
Thanks for the comments. just finished grinding another 5 blades to do another 5 to the same design. Regards DANIEL TASMANIA.
-
HI , here is a folder i made up ATS34 blade ,ti liners ,including a spoon ,which is an extension of the ti liner.Used for cleaning out the blood on the backbone in a trout. Merry Christmas DANIEL TASMANIA.
-
HI NEAL. i had some reservations about the clearance you mention. To make sure the die holder cleared the slides i ran it without the die attached to make sure i had clearance when the die was attached. A bit of trial error but the whole machine was trial and error. I just about gave up trying to stop it walking about the floor,even with the base plate .400lb and the anvil 500 lb however i did get it running real sweet in the end. the thing hammers real good.
-
Another Tire Hammer In The Works
DIDTAS replied to CurlyGeorge's topic in Power Hammers, Treadle Hammers, Olivers
HI . here is a pic of my tire hammer in action. DANIEL TASMANIA. -
Another Tire Hammer In The Works
DIDTAS replied to CurlyGeorge's topic in Power Hammers, Treadle Hammers, Olivers
HI , I should have added that i have a gap of half an inch between the dies at rest. i machined up the the dies from an old truck axle .No idea what the steel was but i heat treated it and it shows no sign of deterioration after a lot of hammering. Merry Christmas. DANIEL TASMANIA. -
Another Tire Hammer In The Works
DIDTAS replied to CurlyGeorge's topic in Power Hammers, Treadle Hammers, Olivers
HI GEORGE, may be a bit late however i made mine with a two and a half inch offset for a 5 inch travel.i get a bit more travel when the springs load up. regards Daniel TASMANIA. -
Another Tire Hammer In The Works
DIDTAS replied to CurlyGeorge's topic in Power Hammers, Treadle Hammers, Olivers
HI, i welded a piece of 1/8 plate to the inside rim.to make a small internal quadrant oposite the crank throw , i then kept topping up the formed recess with lead till it stopped walking about. a bit of Heath Robinson method but after all i am Scottish. used the hammer through the week to make up some damascus. After the hammering i put the billet through the rolling mill and it turned out great. I think the hammer is well worth building. Daniel TASMANIA. -
Another Tire Hammer In The Works
DIDTAS replied to CurlyGeorge's topic in Power Hammers, Treadle Hammers, Olivers
DANIEL HERE AGAIN. should have mentioned that i had a lot of mucking about to stoping tire hammer walking about the floor.even with the base and anvil weighing 900lb . the weight of lead on the tire rim ended up 11.5 lbs to stop it walking.hope this may help builders DANIEL TASMANIA. -
Another Tire Hammer In The Works
DIDTAS replied to CurlyGeorge's topic in Power Hammers, Treadle Hammers, Olivers
HI RE the drive hub. i used a piece of alu billet 3 inch dia.i think i will wear out before the hub.knurling the hub is not necessary. REGARDS TO ALL DANIEL TASMANIA. -
HI Guys, thought you might like to see a pic of my tire Hammer in action,i am very impressed with the performance. DANIEL TASMANIA.
-
Here is my forge ,yet to be installed.going to use coke.cant show the home made blower as it is up at the shack. aluminium hood .the 6 inch flue might be a bit small. will line with fire brick when in place. DANIEL TASMANIA.
-
hi guys , talked to my scrimshaw man . why not red ink {could he tell the diference} mix a small amount of blood with the ink. incuded some of my liner locks with scrim shaw of tas annimals plus a kiwi bird. he recons blood and ink would be ok. Daniel TASMANIA.
-
Thanks for the kind remarks . will give it a go as is to try it out. have put a bit of the six by four on an one inch thick steel plate for a vertical one as well. will also heat up a bit and try to quench it to see if it hardens. Thanks again . may have a go at hard facing later DANIEL TASMANIA.
-
Thanks for the remarks. cant show any other pic as i dismantled it this morning. i have no room left in the workshop so i built a new shed up at my fishing shack in the highlands. will try to make a bit of damascus when the fish are not bitting. can take few mone pic from all angles if you wait a week ????/ Thanks DANIEL TASMANIA.
-
SAFETY, Yes it will have a safety plate and spring shroud before it goes into operation. Thanks Daniel.