-
Posts
313 -
Joined
-
Last visited
Content Type
Profiles
Forums
Articles
Gallery
Downloads
Events
Posts posted by highlander
-
-
I think that it would mostly be used for pre-heating metal prior to welding. I usually use a rosette head on my oxy/acetelyne torch, but I could also pull a burner out of a forge and use it as a hand held torch. I'm sure that there are other uses, but that's the first that comes to my mind.
Pete
Hello, fellow Delawarean! -
i use a mousehole just like that except mine is a bit swaybacked. nice scores.
-
I looked at that anvil when it was posted for $450. Good to see they came to their senses.
glad to see you are back online again, i sent you a PM -
vise and a drawknife
-
Very cool mike!
-
fuel consumption and efficiency varies a fair bit with different forges. i say buy a bag of it and go to town! see what happens and report back to us.
-
.... are you serious?
-
-
-
-
do you have any coating on that ceramic blanket in the forge? if not buy itc100 and apply it ASAP. ceramic insulation(kaowool, inswool) is a respiratory hazard when hot, plus the flames will ruin it in no time flat.
-
Yeah from day one on planning this I knew it would require a lot of hands on research. Which to be honest is why I really wanted to do this, manual labor has always been more rewarding to me than sitting behind my computer. Just don't tell the other design geeks at my school I said that haha.
That's why I don't do computer work like I used to. -
Vaseline works as pulling lube as well. you DON'T want to use something that will eat at the jacket on the wire or the conduit/tubing. don't use motor oil!!! if you will be pulling a lot of wire(lots of lamps or a long windy run in a lamp) go to the store and buy wire-aide, clear glide or some other wire pulling lube specifically designed for the purpose.
-
hehe ive used a vacuum many many many times to fish through conduit that i cant shove a fish tape in. use a small diameter string like a fishing line and tie a light foam ball or cotton ball or whatever is the proper size for the pipe. go to the other side and turn on the vacuum! if you need heavier duty string, use the fishing line to pull your heavier string into the pipe.
-
Harbor freight sells a chipping hammer for welding (two faced - |) ...if you grind the sharp edges off and round up the new faces you get a dandy two faced hammer for doing that job
the only issue is that its a harbor freight and its probably made of mild steel. It wouldn't hold its edge as well as if you were to use an old chisel or something -
i appreciate all the feedback including yours, mark. the rose was a first, and i decided to go with a thicker closed petal. if you have ever had a rose bush, you know that the flowers don't all look the same all of the time. sometimes they are closed. sometimes they are open. sometimes they are partially open. i am still learning this blacksmithing thing and i will be learning every day until i can't swing the hammer anymore. first rose and first try. next one will be better. i promise.
-
ive tried forge welding with an o/a rosebud and all its good for is wasting gas and oxygen. you dont get enough heat on the whole piece and by the time you put the torch down safely and pick up a hammer its already cooled.
-
spray i down with wd40 every now and then to prevent rust if the air is humid where your shop is (im near a river)
-
-
blacksmiths depot sells them. i think they are under "accessories"
-
Don't got too full of yourself. The more you tell yourself that it is going to be easy to learn, the more disappointed you will be. Instead, motivate yourself to want to learn no matter what. No matter how many failures, keep on trying.
-
my first sale was a railroad spike letter opener on eBay. feels good doesn't it?
-
i can see the Delaware river
-
mine is a stanco. very nice. $25
A rose by any other name.
in Copper Alloys
Posted
Copper stem with brass petals. Valentines Day gift for my mother.