CurlyGeorge Posted July 21, 2009 Share Posted July 21, 2009 (edited) Well guys. I got lazy. I decided that I didn't want to keep stomping the treadle to bring the hammer down. So, after some thought (and, YES, that hurt), I finally figured out a way to motorize the thing. Here are some pix of the final product. It ain't pretty, but that 16 pound hammer really smacks the anvil!! I hope these posted OK. I'll be firing up the forge, tomorrow, and trying it out. I know that it cycles and hits the anvil hard. I just hope that it works on the hot iron. I hope that I have it set up right. If you hear what sounds like a big crash, you'll know that I'm back at the drawing board. :D Edited July 21, 2009 by CurlyGeorge Quote Link to comment Share on other sites More sharing options...
arftist Posted July 21, 2009 Share Posted July 21, 2009 Can't wait to see your report. Looks great to me. Quote Link to comment Share on other sites More sharing options...
welder19 Posted July 21, 2009 Share Posted July 21, 2009 Interesting looking, would love to see a video of it opperating if you can but if not it will be nice to hear how it works. welder19 Quote Link to comment Share on other sites More sharing options...
Jesusdude Posted July 21, 2009 Share Posted July 21, 2009 Classic! Way to go! Quote Link to comment Share on other sites More sharing options...
Marc Posted July 21, 2009 Share Posted July 21, 2009 Looks like a nice bit of work - Not bad for a "lazy" guy :) Quote Link to comment Share on other sites More sharing options...
Bentiron1946 Posted July 21, 2009 Share Posted July 21, 2009 How long ago did you study under Rube Goldberg? He would be so proud of you! Looks good! Interesting little helve hammer.:cool: Quote Link to comment Share on other sites More sharing options...
CurlyGeorge Posted July 24, 2009 Author Share Posted July 24, 2009 Well, my report is not so good, for now. The hammer cycles slow and I can move more metal hand hammering that I did with the motorized version. Stan is comming up, on Saturday. So maybe he will have some ideas on how I can tweek more power out of it. I'll keep you posted. If all else fails, I know that I can go back to treadle power and pound metal hard. :D Quote Link to comment Share on other sites More sharing options...
Nakedanvil - Grant Sarver Posted July 24, 2009 Share Posted July 24, 2009 As best as I can tell from the pictures, you have a 1750 RPM motor on slightly better than a 2 to 1 drive ratio. That's trying to drive the hammer at something like 700 or 800 beats per minute. It pretty much can't be done, you're either stalling out the motor or slipping the belt or some combination of both. Once you get a proper ratio (I'd go for about 120 to maybe 150 TOPS) you'll need to make sure that the idler pulley is on the slack side of the belt. The motor "pulls" one side of the belt tight, putting all the slack on the other. If the idler is on the tight side of the belt, when the belt tightens it pushes the idler away requiring you to press harder on the treadle. I've seen a lot of hammers set up wrong and run 100 times better just by reversing the motor. Next, you'll need to introduce some elasticity in your drive. If you look at any mechanical hammer ever made you'll see springs in the system somewhere. Click on this link:YouTube - The Original Junk Yard Hammer This is a hammer I built many years ago. Look at the springs on the drive. They give it "whip" and allows for different thicknesses of material. I'm not particularly reccomending that setup for your hammer, just showing the principles. There are hundreds of ways to do it. Quote Link to comment Share on other sites More sharing options...
Ratel10mm Posted July 24, 2009 Share Posted July 24, 2009 For all that, I reckon Heath Robinson would have loved it! :D Quote Link to comment Share on other sites More sharing options...
CurlyGeorge Posted July 24, 2009 Author Share Posted July 24, 2009 Thanks Grant. I watched your video a few nights back. That's some engineering!! I have a spring inside the pipe, connected right under the hammer handle, on the drive connection. That spring compresses and allows for different thicknesses of metal. But I think that you are right about the pulley ratio. Stan's comming up, tomorrow, and we're going to go over that. Thanks for the advice. I was hoping that someone with build experience could look at it and see something wrong. That sure gives me a place to start. I'll let you know what we come up with. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.