Jump to content
I Forge Iron

What finish should I use for blades and knives?


Recommended Posts

So I've read through here a few times but I can't seem to find the answer to my question, so, what sort of etch/finish should I use for blades and knives that will prevent rusting but also not ruin the heat treatment? Also, if anyone can tell me how to blacken blades that would be appreciated, as well as if anyone has any information on russeting.
Thanks in advance.

Link to post
Share on other sites

I can, kind of. You see, I work with a lot of scrap steels due to all the illegal dumping that happens around where I live. There are a few individual pieces of steel I have ordered but outside of that all I can tell you is high carbon, low carbon, mild, wrought or rebar. 
Do you know of any finishes that would make high carbon show up as a black/dark grey?

Link to post
Share on other sites

Any of the finishes used on guns can be used on blades; though some I would not use on blades that will be in contact with food.

I've seen some mirror polished black finishes on blades at the Knifemakers Guild Show.  Hot blued as I recall.  Do you have access to something like "Firearm Blueing and Browning" by R. H. Angier?  (Wow, I picked up my copy used for about a US$1 Back a number of years ago!; Do they have something like ILL where you are at?)

Just for fun try boiling a polished and degreased blade in very strong black tea and see what colour you get on a plain carbon steel. (212 degF, 100 degC is way too cold to affect the temper; but make sure that the blade tip is not touching the bottom of the vessel where the "pot" may be hotter than the contents.)

Tannic acid can be made from plants.

Link to post
Share on other sites

"When a group of researchers compared the tannin content of coffee with tea, they discovered that green coffee contains around 0.7% by weight in tannins, roasted coffee around 1.8%, and tea up to 3.7%."    from findanyanswer.com

Link to post
Share on other sites

I've gotten some nice blackened finishes by simmering a cleaned piece in hydrogen peroxide for about five minutes or until evenly rusted then cleaning with denatured alcohol and simmering in distilled water for about ten minutes then coating with wax. 

Pnut

Link to post
Share on other sites

In general the higher the carbon content the less it will darken in the etch. Of course alloying metals can alter this considerably.

If you're using mystery steels you'll probably need to make test coupons and keep notes. Use the metals in your pattern welds grind to the finish you like and cut small coupons, say 1" lengths and etch. Vary: recipe, strength, time, temp, etc. and keep notes of every change.

Make ONE change at a time and test, making multiple change means you'll never know what did what.

Frosty The Lucky.

Link to post
Share on other sites
  • 3 weeks later...

I use 80/20 of ferric chloride and white vinegar to achieve the grey etch below.  I primarily use 1084 and 8670 steel.  j

sand to 800/clean with acetone/clean with water and Dawn dishwashing soap/rinse/dry

4 min in the etching tank/take out and neutralize with windex, scrub blade with 0000 steel wool/dip in water and rinse/  dry off and repeat entire process. 

then I stonewash. 

these two are 8670

Alaska.jpg.f4849b4d0dcba0e9988bc4e42fe90abf.jpg

These are 1084

IMG_2282.jpg.9f7edf067552d12c974ea588262ee918.jpgIMG_3233.jpg.9b85552504c060ba7cd48e0f9476ad2e.jpg

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...