dogblazer9598

anealing a hammer

Recommended Posts

I would not think you need to do anything to your hammer.  I use several hammers from my stash, all of which have some degree of heat treating to preserve the hammer face.

Share this post


Link to post
Share on other sites

Can you tell me how hard/brittle my hammer is and how hard my fuller is?  What alloy my hammer is made from?

Share this post


Link to post
Share on other sites

Take the head off the handle, heat the head to above critical temperature, allow to cool veeeeeeeeeerrrrrrrryyyyy slowly in vermiculite, wood ashes, or powdered lime. Re-handle. Mark the handle SOFT.

Share this post


Link to post
Share on other sites

appreciate the reply but I do have a dumb question .how do I find the critical temp ?  pardon my ignorance but im very new to this .

 

thank you doug

Share this post


Link to post
Share on other sites
22 hours ago, dogblazer9598 said:

how do I find the critical temp

For more critical applications, like blademaking with thin crossections where you need to limit grain growth and are planning on hardening it is more difficult as you need to be very accurate.  For making a soft hammer head, I would just temper it very soft using a sub-critical anneal (in the 1275 deg. F range).  If you work in very dim lighting and bring it up to a point where it is just showing a little bit of red, then hold it there until the heat soaks all the way through the hammer head, I think you should be fine.  As John mentioned, then let it cool very slowly in an insulated container. 

The difficulty will be holding it at the low temperature until it is thoroughly heated.  Fortunately since grain growth isn't really an issue you can exceed the dull red temperature on the surface if necessary.

Your other alternatives are to use a brass or copper striking hammer (Harbor Freight has a cheap brass one for around $25, and you can sometimes find them at flea markets) or weld a sacrificial piece of mild steel to the top of your fuller or guillotine tool.  Personally I prefer not to have soft steel hammer heads in my shop, but each to his own. 

Share this post


Link to post
Share on other sites

Here's another direction you may want to consider. Rather than softening a hammer, depending on the design of your guillotine, you could weld a small slug to the top edge for a consumable contact point. This would focus the impact. Or you could just take the top die out when it begins to mushroom, throw it in the forge and re-shape the top surface back to flat.

Share this post


Link to post
Share on other sites

I have a sacrificial piece of round stock welded to the impact area of the top dies. Keep the edges dressed if they mush over and replace them if needed. 

Share this post


Link to post
Share on other sites

Arkie, yes, only mine is a guillotine fuller. Each top die has a sacrificial piece of round stock welded on. It makes a great target for the hammer (grin)

 

To answer a previous question, try Heat Treating, general discussion

A2 is the transition point where when heated metal becomes non-magnetic. You can find this by hanging a magnet from a thin wire and bringing the heated metal CLOSE to the magnet. If the magnet is attracted to the metal, you are not at A2 yet. If the magnet is not attracted to the metal, you are at A2 or above.

 

Share this post


Link to post
Share on other sites

I need to make a guillotine fuller.  Sometimes the angles on the scissor type create problems.  Straight up-and-down works better on lots of things.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.