Sign in to follow this  
Leeknivek

changing shielding gas in tanks?

Recommended Posts

I've got a bottle for my mig welder - 75/25 argon/co2. For the little bit I use the mig welder, I usually just use fluxcore. I want to teach myself tig, and my tig regulator fits onto this tank - but I have read that tig likes 100% argon. I have also read argon/helium mixes are good for both mig and tig. 

When one gets a tank refilled, can the tank be refilled differently than what it was previously? Can I use this 75/25 tank for straight argon? What's a price I can expect to pay?

Share this post


Link to post
Share on other sites

What did your local welding supply place tell you?  They might be willing to trade bottles which would save you the flush charge.  Getting friendly with a good welding supply is worth a lot of money.  I once needed to do a lot of cutting and my local shop was willing to lend me the big O2 bottles with just a credit card number in case I didn't return them.

Share this post


Link to post
Share on other sites

I seriously doubt any supplier will put a different gas in a labeled cylinder but as Thomas said, they might swap it out for 100% argon.

Share this post


Link to post
Share on other sites

Haven't been ... yet. I got the tank through craigslist when buying my MIG welder. It's been empty so I just run fluxcore. The only one I have around here was Abco - but I think that's Airgas now? I'll have to check them out next time I'm in that area. 

I also found that my tig welder is not actually a standalone piece but a HF arc stabilizer - something I'll have to plug into my stick welder. Know anything on these? 

Share this post


Link to post
Share on other sites

Bottles are generally color coded for the gas or gas mix they contain. Some bottles such as acetylene, by design, can only contain that gas.

Edited by Dodge

Share this post


Link to post
Share on other sites

Bottles are generally color coded for the gas or gas mix they contain. Some bottles such as acetylene, by design, can only contain that gas.

Ironically it's the exact same threading for acetylene and propane, CGA-510 or CGA-300 depending on the tanks used, but they're completely interchangeable. I think CGA-510 is also the old bbq grill threading. But as to what the original poster asked, my local AirGas has exchanged cylinders when I wanted to switch gasses and yours should too, as long as it's in date. Which btw is a good way to keep your tanks inspected.

J

Share this post


Link to post
Share on other sites

Most of the time these cylinders aren't filled on site anyway.  Usually the supplier will trade with you.  I really depends on the supplier and how cantankerous they want to be.  I will usually trade out unless there is a problem with the cylinder.

Share this post


Link to post
Share on other sites

Ironically it's the exact same threading for acetylene and propane, CGA-510 or CGA-300 depending on the tanks used, but they're completely interchangeable. I think CGA-510 is also the old bbq grill threading. But as to what the original poster asked, my local AirGas has exchanged cylinders when I wanted to switch gasses and yours should too, as long as it's in date. Which btw is a good way to keep your tanks inspected.

J

Agreed on the threads, J. What I meant about gas specific, was the porous material (cork?) that fills acetylene bottles to maintain its stability. And yup, my supplier will trade bottles for whatever you want. Also agree about keeping bottles up to date. Unfortunately, Its been so long since I got refills, I surely will be paying inspection fees next time :o

Share this post


Link to post
Share on other sites

This really isn't the place to be asking, a phone call to the local welding supply will tell a person what they need to know. Rules change place to place so log as they need code. What the local outfit will do has nothing to do with what one even 12 miles down the road.

Frosty The Lucky.

Share this post


Link to post
Share on other sites

Chances are high you can get yourself 100% argon. As mentioned, my place will swap similar sized cylinders for other gasses no problem. I regularly swap mig gas for argon, Nitrogen for O2, or what ever, depending what I may need an extra cylinder for.

It's also possible to have them vacuum and purge the cylinder, so you can use the same cylinder for a different gas ( within reason if they take the same CGA valve). It's what most places do anyways when they swap cylinders at the refill center. Smaller operations  that fill themselves though charge extra for this.

 

As far as your HF box, what's your question? You really don't need an HF box to do basic scratch start tig with any DC stick welder. You'll need an air cooled tig torch with gas valve, plus torch consumables (tungsten, collet, collet body, cup or gas lens parts. All these are usually based on tungsten size with the exception of the cup), a power block and a gas hose and flow meter to hook up your argon, and obviously 100% argon gas. Infinitely adjustable DC stick machines work better than those with fixed taps as it allows you to better fine tune your amps for what you are doing. With any of these set up, you will not have remote amp control, even if your HF box has a pedal. If it does, all that does is turn on/off the power and HF, not make amp adjustments like it does on a dedicated tig machine. The pedal on an HF box does make starting/stopping a bead easier than simply doing basic scratch start, but it's not required.

If you have an AC only stick machine, you are sort of out of luck. AC tig is used for alum and for that you would need continuous high frequency to maintain an arc. However a dead basic Ac stick machine is tough to do alum tig with as you have no amp control. I've seen it done, but you have to have a lot of skill to pull off good results. HF boxes are often used with engine drives that have both AC output as well as a pin connector that allows remote amp control ( the older Ac capable Miller Trailblazers are a good example)

 

If you want to rig up your stick machine for tig, let me know. I'll need picts and good descriptions of what parts you already have, and I can tell you what will or will not work, and what you may need.

Share this post


Link to post
Share on other sites

Since I worked in the industry I can answer this accurately.  The paint codes on cylinders are decided by the manufacturer.   Argon/Helium/Nitrogen are inert gases and so filled in cylinders with a fitting for inert gases.  Mixtures of those gases that  are inert follow the same formula and use a connection Called CGA (compressed gas association) 580.  If you own the cylinder they are able, legally,  to fill it with any of those three gases no matter what the color of the cylinder is.  This does not mean that the specific distributor  or its corporate connection will not add additional handling charges.   Most mixtures used in welding will also have a CGA connection of 580.  The only problem comes when there is Carbon monoxide/Hydrogen/  in the mixture which may require different Cylinder valve connections and also change the retest cycle limit of the cylinders.  Mixtures containing Oxygen may or may not have a 580 valve depending on the concentration.   Cylinders of pure oxygen have a CGA connection of 540.   Most Gas suppliers have little pocket books  with a load of useful information, applications and cylinder labeling for their product line.

Gas cylinders are not "flushed"  They are blown down and vacuumed.  Purging a cylinder only happens when you return a cylinder with no residual pressure. Gas mixtures are usually filled by pressure using a formula worked through engineering data and experience with the particular  equipment. For a gas mixture this means starting at a vacuum. You and your supplier will both get along better if you return the cylinder with 150 psig. remaining.

  

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this