Jump to content
I Forge Iron

Alaric Powell

Members
  • Posts

    9
  • Joined

  • Last visited

Posts posted by Alaric Powell

  1. I think we're good. I haven't lined or coated the forge, as yet the materials are in the mail.

     

    Two questions: Can anyone point me to the post for materials for the T-burner? 

    Is there anyone in North Ga. Who has blacksmithing materials available for sale?

    I would go visit Wayne, but the current social situation dictates I should avoid contact with him. No offense Mr. Coe.

  2. Right, so, I think I'm on the same page. If my test block has too many ports and thus has too little back pressure, I'll reduce the number of ports and spread them out over the surface, increasing the pressure and attempting to maintain the coverage relative to my flame face below. Which, in turn, will allow the radiant heat to reflect back into the forge with the assistance of the IR coating and bring the temp up (sooner?)

  3. Wow, don't know how I fudged that SOOO bad (EDIT: I multiplied the DIAMETER instead of the RADIUS, OOF!) , was operating on V=πr²×L (3.14 x 16 = 50.24, x 16=803.84in³) The 7x11 interior would come out to about 423in³ (add salt because my math is rusty <obviously>)

    Anyway

    Link to 3D concept: https://skfb.ly/6RRMJ

    And Picture: the measurements below are Interior on the top box and Exterior on the cylinder body

    Dimensions_Resized.jpg

  4. Sorry Frosty, finally recovered the password for my original account. I'm building out of an old air storage tank (the kind you pump up with a compressor) it's 16" Long with a 12" Diameter.

    I cut both ends off so I'm left with an open cylinder. With both ends closed with soft IFB (obviously it won't operate fully closed :)) and 2" of wool, rigidized and IR coated, the volume is +/- 3200 in³. The opening I cut into the top for the ribbon burner is 4.25" wide and 10.5" long (area of about 44.5 in²), leaving 2.75" on either end. 

     

    I was planning on running forced air into the plenum as that's what Wayne suggests in his build, then I ran across this post and had to stop in to look. I really like the idea of being more portable without the need of a generator or other nearby electrical source.

     

    So, long story short. Before I start haphazardly welding things together.  Do you think one of the MIG tip style delivery systems you like will perform well in this situation? OR, Do I need to scale down and use a smaller shell?

     

    Regards,

          Alaric Powell (AMPowell)

  5. Currently I'm in NE Ga. 'bout 4 hrs from you, Wayne

    Oh, and feel free to tear my design to shreds! I'm no Snowflake. The whole reason I'm here is to learn, and that works best if you have mentors willing to tell you where you're going wrong, I'm not trying to repaint the shop walls with my charred remains.

    Currently making my way through Mikes book.  Took his advice from 101 and downloaded it from Scribd.com.

    The Design I made was based purely off what images I have seen online, with absolutely no Idea of the size/shapes that are required to A: Work, Period, and B: Work efficiently.

    I use Blender as a Graphic Designer and was playing with shapes; when I do know more about the process I'll more than likely, again, render it in Blender before I build it.

  6. Hi all,

       New to the forums and to smithing. I see a lot of good info here, so I wanted to ask the question. To build or to buy? I've seen a lot of forges online  priced $350 and up, that's a big pill for a newbie like me, so I was wondering if it'd be cheaper/smarter to build. I need everything for anvils to hammers and would like to be as economical as possible. So i did some googling, found this site, bummed around Amazon and eBay, and I noticed that buying the materials plus shipping as about the same if not more than buying a pre-made forge. Now, all I looked for was sheet metal, Fire brick (3k degree), KaoWool, and rigidizer. No itc-100, and I figure I can make some Sodium Silicate Glue. The big questions I have are:  Can the Perlite-n-Playsand DIY bricks hold up to the heat as well as the Factory made? Is there a DIY KaoWool equivalent? Is the ITC necessary on the forge walls/Ceiling? I have a supply/warehouse within 15  miles of home so sheet metal and Stock shouldn't be an issue. I have drafted a forge design from some pics I have seen around, I also have several tanks around the house (Propane, air tanks, Grills) that I could chop up If my design isn't feasible, seeing as I built it around what I found on eBay for what looked like cheaper than average prices.The bricks I found are keyed so one would need cut in half to square the ends for the forge floor.

    The inner cavity of my design seems to come out to: 9.5"W x 3"H x 17"L

     Pics ahoy and thanks for the help in advance!

    Cut Key Brick Layout.bmp

    Base.png

    Exploded.png

    No Case.png

×
×
  • Create New...