Melw45

Finally getting settled and have some time to start on my new shop building. My dad and I got the foundation dug out and will get the forrms in over the next few days. That is if it doesn't snow. Mel W.

Nice poker. That Dragon and twist would make a cool walking stick handle. Thanks fo e sharing. Mel Than

Very cool. I can see tbem on the office shelf in a auto shop. Mel

So is the anvil hollow? Mel

Well this is on hold for now. The grinder and the rest of my shop are packed up because of the move. I will post whin I get back to it after the move. Thanks for looking! Mel

That turned out very nice. I bet the church is happy with it. Mel

I am setting up a 2x72 grinder/sander. Breathing metal dust might aggravate my asthma. All joking aside metal dust is bad juju! I am still waiting for the mask. Last tracking had it out for delivery then changed to incomplete address. I called the usps and used the tracking number to schedule a delivery and gave the robo phone machine my correct address. Here is hoping it worked. Mel

Dylan Thanks for that lead. Mel

Wood What are you useing for the engine? Looks like a neet project. Mel

Update on this project. Went by Harbor Freight and picked up a linked v belt and a grease gun for the bearings. I was able to use a 25% off coupon. Now all i need is to get some abrasive belts. Any one have a good supplyer for the belts that wont brake the bank? Thanks Mel

Judsson Nice railing. Mel W.

That looks beefy. What is the HP on that motor? Mel

Frosty How about some photos of yours? Mel

I got this in the mail today. Just need to get vbelts and sanding belts. Mel

I have one of these masks on order. I will be looking in to converting it to a blower based fresh air system If that is not feasible I may have to shave. Mel

Look at this photo. The red arrow is the tracking adjustment. The yellow arrow is the arm that tightens the belt. There is a spring that goes just about where the arrow is pointing. I have not instaled it yet. I wont be welding this unless there is a problem with it staying together. Mel

I just tried the new bearings. Clamped them down and with a wack on the shaft they lined up ant turned free. Looking good now. Mel

The new pillow blocks arrived today. I will be clamping them down to see if they have the same problem. I will post how it go's later. Mel

Lbs I like your hammer. I showed it to my wife she said it was pretty. Good job! Mel

I might add a plate to the top. I would like the bearings to be further apart. They seem to be to close. I have heard of one guy that said he was breaking drive shafts. I think he might have had too much spring on the tension arm. Mel

Gas. Mel

My wife ordered me the step pulleys and i have ordered new pillow blocks. The new one are self aligning Mel

Only one available. So i bought all they had. Silly guys wanted $99.00 for the rest. Have to build one first. That is a idea though. Mel

Yesterday I went to harbor freight for some tie downs. Did get them. They had some open box items marked down over 90%. I scored a 6hp motor for $8.00. I guess it was a surprise to the guy that rang me up. He did not seem happy about it. Still sold it too me, reluctantly. Mel

I was pleasantly surprised as to how nice it was. I bought it new from harbour freight years ago. My uncle came by to look at it after I got it set up. He is a machinist and i think he wanted it to be bad.but it tested out very good, flat and true. When i moved it in we had 5 guys to get it out of the truck and on the stand. I moved it out with a hoist by myself. The wife standing by in case of catastrophe. The worst thing was the wheel of the hoist stopped in a crack in my driveway. Needed a pry bar to get it out. The funny part was getting my wife to sit on the trailer tongue to stop it from rising. Pushing that mill uphill just was not going to happen. I had to convince her it was not a comment on how much she weighed just leverage. Mel