James Walker

  • Content Count

  • Joined

  • Last visited

About James Walker

  • Rank
    Junior Member
  1. You could buy the #110 anvil from Harbor freight for ~$70, take a torch or other cutting tool and cut out the shape you want, then drill a huge hole in it with a drill press. Then get a solid 1inchish bar the length you want and weld it into the hole. You could probably get a decent looking #50 steel hammer out of that anvil. Personally I would get a block of wood and put some heavy steel plating on it and weld them on somehow, then use that solid bar and mount it in somehow. You could get the same size as the solid steel anvil, but it'd be like 10-20lbs.
  2. Thanks for the kind words. Those steer heads look very impressive to me. I'm having enough difficulty simply drawing out the steel bar, much less anything else Someday I'll make some like them! Next time I mount an anvil I'll have to try some silicone sealant. The job I did for this one is just fine, hardly any ring at all. About the CO poisoning: I'm actually fairly concerned about it and have made a decent attempt to avoid it. I have a CO detector right by my forge and have set up an array of fans to try to get some air circulation going in my garage. I'm still undecided on where to put the fans but currently they're like this: Both doors have windows that I dismantled to put the fans in. The two windows are permanently shut, but I might take one out and move the inside-fan into it. I'd like to keep the intake fan on the other side of the output fan (with my forge inbetween), so I'm primarily breathing in the input fan air, but don't really want to mess up my window for it. And I still need to worry about where to mount my leg vise if I can ever find one for a good price.
  3. Thanks for the reply. As promised here's a few pictures of my shop so far. The blankets are covering the garage door to muffle the noise a little. I mounted the anvil on the stump with a cable, tightening it with two screw-hooks. The vibration was knocked down quite a bit to a decent level. Just for fun I got some heavy chain and wrapped it around the base of the anvil as tightly as I could, the noise went down even more so I just kept it there.
  4. I found this tidbit and am willing to try it a little more. I tried getting the strike of my hammer on hot steal to 'rebound' the head such that it drives it to cause the hammer to be verticle, but I had no success. I suppose I'll try some more.
  5. I read that article last night and tried it. I think it worked a little but I already knew from previous jobs not to grip the handle too tightly. My problem is at some point my wrist needs to support the rotational force of the hammer head as I lift. I'm hoping that it's just me wrist getting used to the weight. My anvil is right at my knuckles while I stand with my boots on and hang my fist loosely downwards. Like I said it's not painful, I'm just trying to be careful with my body while I start out blacksmithing so I don't erroneously damage it. I'm thinking about buying Hofi's DVD.
  6. Update: I moved to my new house. It's deep in the woods where I can blacksmith without being too noisy. I also built my forge and mounted my anvil on a stump. I found an 8" x 3/4" steel bar and have been making it into a pair of tongs using Larry's instructions: tong making - Blacksmith Picture Gallery and have been mostly successful so far. I had a few questions though, about hammer technique. I figure that now that I have an anvil, a forge and a set of hammers, I should learn as good of hammer technique as I can so as to preserve my mostly healthy arm. I've read what I've found on hammer technique (including this thread: http://www.iforgeiron.com/forum/f7/hammering-technique-10/index4.html ) and seen a few videos but haven't found answers to these specific questions. Keep in mind that my experience is entirely limited to working a 3/4" steel bar with what I think is a #3 hammer. 1. When I hammer I inevitably get tired in my wrist. It's not really pain, my wrist is just tired of picking up a hammer every second. I've trying choking up, and I'm going to try using a lighter hammer (I don't know how heavy my current one is but I think it's #3). Is there anything I can do for this? Or is this just because my body isn't used to lifting relatively heavy objects in that manner and my tendons get tired? 2. I've been looking for videos of good hammer technique and haven't seen anything that really shows the 'best' way to use a hammer. I imagine that the 'best' way is variable based on 1. Body build, 2. Hammer, 3. Type of strike, 4. Material being hit. However I'm still learning basics like where the elbow should be located, how high to raise the hammer etc. 3. When I don't have any metal on my anvil face and I hit it with my hammer, it rebounds. When I put some bright yellow steel on it, my hammer hits it and is dead. It seems like 100% of the work in lifting the head is done by my wrist. Is this normal? 4. Has anyone every heard of putting the anvil at a bit of an angle (Such that the anvil face is leaned towards the user maybe about 20-30 degrees). This would detract from the power of gravity forcing the hammer down but would make it much easier to raise the hammer away from the anvil, distributing the load between the flexor muscles (which are doing almost all the work currently to raise the xxxx thing) and the extendors. 5. How does me being tall with long forearms and relatively thin affect how I should hammer metal? Thanks!