Jump to content
I Forge Iron

territorialmillworks

Members
  • Content Count

    495
  • Joined

  • Last visited

Posts posted by territorialmillworks

  1. I have a 25 year old Grizzly lathe that has been worked hard.  The motor fried and took some of the control relays with it.  DOA...  So now I need to wire a replacement motor with the ability to reverse the rotation by means of a transformer/contactor and switch.  I've considered using two knife switches for KISS purposes.  Any help would be greatly appreciated.  Thx , Keith

     

     

  2. .I had a Norgren valve fail almost out of the out of the box..Got to say it..Run from Norgren  Virtually no customer support.  You can't rebuild them (no parts), Low CV   They couldn't give me a replacement because they didn't have any at the factory and none at any of their distributors.  Told me to wait till the next production run of that model. Didn't know when !     Contacted  PARKER, outstanding customer service.  Walked me through my application and they had parts on the shelf. # B834OOOXXA  If you see green grease seeping out of the Parker valve, it's just assembly grease.  This valve has been running 5 + years.

    Keith

  3. The inside jaws have been installed on my lath for years and I've marked them to match the chuck.  But today, I needed the outside jaws to hold a large piece.  That's when I realized that those jaws were not match to the chuck.  Spent a bit of time using the "hit and miss" method.....then shut off the lights and went inside.  Even a fool knows his limits.  So what is the secret, math formula for timing these jaws to meet in the middle..........THX, Keith

  4. Last week, I went  looking through my scrap pile and came up empty. So, I decided to scrap all the "unusable" pieces since  I was going into town anyway to my steel supplier. I had 500# of steel and a little brass and bronze and copper scraps that I set aside.  When I'm done, that little bit of brass/copper brought more than than all the steel. I figure that it paid for my gas and bought me lunch.  Oh well, now I have room to start saving scrap again !

  5. There is a 50+ foot run of 1/2" black pipe from the compressor to the shop with a second inline 80 gallon tank at the shop. The line is above ground. The set up leaks down and the compressor kicks in at night which is inconsiderate of my neighbors.  I have "soaped" every part of the lines and compressor repeatedly and still can't find the leak. I've considered freon dye but have no idea what bad things that could cause. I fully realize that I could simply close the valve at the compressor but that would require my arthritic mind to remember to close said valve.  It ain't going to happen.  Any thoughts?

  6. We have Sonoran desert tortoises in our backyard.. The oldest is Festus, who is between  70-80 years old. Oddly enough, they are attracted to the vibration of the power hammer. 

    Recently, I've watched hairline cracks form around the PH and now the cracks have widened.   Turns out that these tortoises have burrowed  more than eight feet under the shop's foundation, terminating directly under the hammer ! ! !  Come spring, I'll extract the tortoises, saw cut the floor and pour concrete until full.....Just weird enough to share with others LOL

  7. Yes, I forgot to post content. I could do better if I weren't dyslexic, bald and hearing impaired LOL  This is my take on a 20 ton Carolina style press.  The 1/4 thick angle iron rails spread when in use, so I used 1 inch square bar for spacers.  The bottom platen took some tweaking to get plumb/square. I'm impressed by how much work I can get from one heat.  This really adds to the versatility of a power hammer.  Besides, the grand kids love to 'smush' coke cans !!

  8. I've known the folks at the local steel supply for many years.  I never buy in large quantity but I do buy frequently.  And they give me their deepest discount....?cause they like me or because they like donuts ?". I mention that the flat dies in my hydraulic press are mild steel and they deform rather quickly.  Sitting at his desk, he tells me to go to the first building, third rack, far end on the bottom is a 2 X 3 foot piece of A/R plate.  Next to it is 30" of  2 1/4" round bar, Blanchard ground used for hydraulic piston shafts.  You can have that too if I want it (cause it has some surface rust.)     Amassing memory, because I can't remember what I had for lunch let alone where a certain piece of steel is in this huge warehouse.  

    So if I cap the flat dies with the A/R, Can I mig weld it without effecting it?   .....................

     

  9. At the steel yard today, the owner threw a 2ft X 3 foot piece of A/R (abrasive resistant steel plate) in my truck.  You got to love free!!!  Can this be welded to a  mild steel base to make dies for the PH and hyd press?  If so, can you share any thoughts on pre/post heat etc? or other uses.  Funny, I didn't know that I need this piece of steel until I got it.  Now I've got to put it to good use.  What a terrible responsibility..... 

  10. How many times have you needed an antique (fill in the blank) only to see it priced on ebay for more than new in the box, or with the price tag still on it ( For real)

    Call it an antique with a fanciful name, Price it at a min of five times the new value.  Charge a stupid amount for shipping and handling. It will sell within a week.  Ebay, got to love it.  Now that i got that out of my system, I'll go forge one of (what ever that was) I'm sure I need one!   LOL

  11. Yes to welding cast. Overhead on the stump on a grader. UUGGLLY.  Hadn't thought about bolting.  Might be tough to drill through the tine. I could cut the hole with the plasma torch and plug weld the studs.  There lies the challenge.  Thanks, I'll let you know how it worked out or didn't.

     

  12. Living in the Arizona desert, anvils are few and far between. Ten years back, I finally bought a Fisher that was in poor condition.  It was swayed back and the parting line between the face and the cast base was very evident. But it was better than a ASO from Harbor Freight.  It is now DEAD.  While getting some plate steel at the scrap yard, I found a fork truck tine @ 15 cents per pound. Considering the condition of the anvil, I'm thinking of milling the anvil and perimeter welding the tine.  I know this is a lousy option but considering its current condition, I don't think it could be any worse.   So jump in and give me your feed back. 

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

  13. I'm blessed with a wife who supports and participates in my blacksmithing addiction.  She can look at my latest effort and provide suggestions about proportion/balance/depth/orientation. I've learned to not just listen to her suggestions but to trust her intuition.

    With her help, we've come up with a list of things that you never want to hear from your "domestic goddess."

    "That's third degree."    Didn't you do that last month too?

    Why would you put a burned tee shirt in with the white clothes? 

    That's going to need stitches.  No, I won't sew it up with a needle and thread!

     You can't go over to my Mom's dressed like that.

    Stop bleeding on the floor.  I just mopped.

    You stink. 

    Not everyone is interested in blacksmithing.

    What happened to your mustache !!!

    No, you can't use my fingernail file to clean the points.

    Leave those cloths on the back porch!

    Don't tell me you did that again !

    Just because it was laying on the side of the road doesn't mean you have to bring it home…

     How many hammers do you have (----) so what's so special about this one?

    You need what ?  We'll  I guess we'll just run down to the bank and take out a second mortgage….

    Why do you always wait till the first of December to make all the gifts?

    Tell me you didn't make knives for the granddaughters.

    Which granddaughter welded that? 

    Just because you can doesn't mean you should…

    When are you going to stop making tools and really make something!

    And finally…..OK Tell me again how you got burned  "There?  NO!  I Won't Help you. You can put the cream on yourself !!

     

    language edited to be G rather than PG-13 rated

     

  14. I'm close to finishing a Carolina clone and share some of your concerns. I welded 1" square bar between each pair of up rights for more rigidity and to keep them from spreading apart. I also overbuilt both platens.  I pre-assembled the frame with 1/2" grade 8 bolts to insure everything was square and plumb before welding and cycled the cylinder with compressed air to check for binding.. I'll probably leave the bolts because, well they're already there and kinda look art-deco. 

     

  15. I got a Grizzly 9742 miter band saw 4 years back that I use a LOT. It's not a high production model saw but meets all my needs.   One day I'll replace the o-ring in the hydraulic feed and replace the blade guide bearings.  The only blade failures have been due user errors:  too fast of feed rate or not lubricating on thick stock. Definitely worth the bang for the bucks.

  16. The product was crushed granite graded through a series of screens for different grades used in carpet/cosmetics/ pharmaceuticals.   

      And then there was a time when they put a live bobcat in one of the guys pickup truck.  The bobcat was under the seat and when he started to drive off, the bobcat clawed it's way up his leg which then caused him to abandon his moving vehicle.  Well, the only I can add is "TENNESSEE"  Well, there was this one time.........

×
×
  • Create New...