-
Posts
925 -
Joined
-
Last visited
Content Type
Profiles
Forums
Articles
Gallery
Downloads
Events
Everything posted by SmoothBore
-
Most useful tool in your shop ?
SmoothBore replied to Glenn's topic in Blacksmithing, General Discussion
Every job eventually winds up on the belt sander, wire wheel or bandsaw. -
I'd go with Saddle Soap and then a coat of Neatsfoot Oil. .
-
Since this appears to be a repair rather than a new piece, an "unconventional" but effective approach, might be to use a little "Red Loctite" thread locker when you assemble the stud/rivet into the piece. .
-
Ballheadrivets on both sides
SmoothBore replied to LeMarechal's topic in Blacksmithing, General Discussion
If I wanted a ball on both ends, I'd make them work like Cutlery Rivets. . -
Raise/Lower BBQ Grill - designs?
SmoothBore replied to Whiskeymike's topic in Blacksmithing, General Discussion
I'm doubtful that there ARE any "authentic" examples. Barbecue grills are very much a "mid-century" American affectation, whose popularity was directly influenced by the surplus of commercially made charcoal briquettes.. A "Brazier" is a much older, more widely distributed system. . -
Hilo forks, forklift forks composition
SmoothBore replied to Ericsg's topic in Blacksmithing, General Discussion
They're probably worth more to someone wishing to use them as forks, ... than as unidentified scrap. This whole notion of destroying useful things, ... just because you can, ... strikes me as short sighted. . -
Nope. Much like the highly touted Unicorn, ... there is no such thing as a "standardized" color code. Every mill and broker has their own codes, ... which may, ... or may NOT, ... be comparable with other brands. "Globalization" has most certainly NOT helped untangle this issue. .
-
Those "sparks" are the carbon burning out of the steel. When the carbon is gone, ... it's no longer steel. Since we don't know the specific alloy, we have no way of knowing what it IS, ... only what it's not. .
-
It was most likely trimmed off a new section of rail being inserted into the existing track, ... or off an existing section, that needed to be "shortened" in order to "set the gauge" of a curve in the track. .
-
Been using a little piece of 5" channel as a cutting "saddle" for a couple of decades now. No complaints so far. .
-
How to mark anvil and vise
SmoothBore replied to Farmall's topic in Blacksmithing, General Discussion
Well, here's the thing ..... You first have to recover lost or stolen property, before you can begin to prove ownership. Guns and cars are thoroughly stamped with identifying numbers, ... but are still routinely stolen, ... and never recovered. If I thought I needed to worry about the theft of "loaner" tools, ... they would never leave my shop. Now, that surely is a sad state-of-affairs, ... but there's no virtue in being a victim. If the organizers don't want to take responsibility for borrowed property, ... then I'd be reluctant to get involved with their event. . -
Looking for help in Pittsburgh Pa
SmoothBore replied to WmHorus's topic in Blacksmithing, General Discussion
In my experience, the folks around the "Steel ( Steal ? ) City" aren't always xxxxxxxxxxxxxxxxxxxx, ... but it's doubtful that anyone is interested in accepting the liability that would attach to such a project. . -
Trailer house steel
SmoothBore replied to Davishomesteadandforge's topic in Blacksmithing, General Discussion
DO with it ! ? The ONLY thing you can ever DO with a chunk of scrap iron, ... is make a big ole honkin' BLADE ! That nobody will actually use, ... for anything ... ever. . -
Neighbors with noise conpliant
SmoothBore replied to Alex w's topic in Blacksmithing, General Discussion
A foot ( dead man ) switch on your electric blower, will prevent over heating your work. -
Neighbors with noise conpliant
SmoothBore replied to Alex w's topic in Blacksmithing, General Discussion
You might try playing some very loud and annoying music, ... to cover up the sound of your hammer. Here in America we'd say, "give em' something to cry about". I think the British axiom might be "hanged for a sheep as for a lamb". . -
The EPA is only as tough as the Administration that supports it's regulations. The current Administration has been rolling back "regulations" at a never-before-seen rate. ------------------------------------------------------------- Now here's the thing that's much harder to quantify. "Prices" expressed as numbers, are totally irrelevant. Whether something costs a dime, ... or a dollar, ... is meaningless, until you weigh-it-off against how much of your precious TIME and LABOR you must expend to acquire any particular item. If you're flipping burgers at minimum wage, a dollar-a-pound for new steel, is expensive. But, ... if bringing the high paying manufacturing jobs back to your town gets you a much better paying job, that same pound of steel actually cost's you less of your time and energy. .
-
I used "Denim" Shop Aprons for many years, ... but was always setting them on fire. Then my Wife got me a remnant of glove-soft "Upholstery Leather", ... from a Fabric Shop. It's comfortable, ... and protects you like a Suit-of-Armor. ----------------------------------- An "Old School" fix for cotton aprons and gloves used for welding and grinding, was to coat the front with any "old" paint, that would yield a a more spark resistant surface. .
-
Horizontal/Vert or Porta Bandsaw
SmoothBore replied to Danjmath's topic in Saws, bandsaws, hack saws, etc
I use a 16" DoAll vertical band saw EVERY DAY. Don't know how I got along all those years without it. Next most useful is the horizontal cut-off saw. Portable band saws have their uses, but are a distant 3rd in my estimation. . -
Yeah, I believe you are. A Bladesmith doesn't use a Rasp because he can't get "new" material. He obviously wants the finished blade to show it's "hand forged" origins.
-
The physical "ability" to perform any task is only a small part of the equation. You can discern someone's underlying "attitude" in a matter of minutes. .
-
Where to get square/round stock
SmoothBore replied to Pr3ssure's topic in Blacksmithing, General Discussion
To those Americans born into the era of manufacturing, it's second-nature to reason, that you should be able to buy ANY commodity, from a business devoted to supplying that material. ( ie: A Tire Store, A Lumber Yard, An Electrical or Plumbing Supplier ) But things change. Here, ... in Southern Pennsylvania, ... many of the wide variety of Industrial Suppliers that existed 20 years ago, have gone the way of the Dinosaur. While the OP's question might initially strike you as lazy or thoughtless, ... I'd point out that my local telephone company no longer bothers to publish or distribute a "Phone Book". Things change. .