-
Posts
255 -
Joined
-
Last visited
Profile Information
-
Gender
Male
-
Location
Weatherford, Tejas
-
Interests
makin' stuff from as many materials as possible & learning new fabrication methods
Recent Profile Visitors
4,259 profile views
-
Try the term "pump rod" also. It might help. TPAAT works on other stuff too.
-
Show me your anvil stands
aessinus replied to pkrankow's topic in Stands for Anvils, Swage Blocks, etc
Scrambler, is that inspired by jlp's "black widow"? I quite like the toe clearance. -
I've used an oxy/acetylene safety cap; just kept sliding it through the coil.
-
Another suggestion, make your rings as a continuous spiral around the mandrel, like a big spring. Gives you leverage from the straight stock & you only have the initial flat on the start where the end is clamped. The rings will come out almost the same size that way. Cut 'em apart afterward.
-
This is all my blacksmithing tools any advice or suggestions
aessinus replied to Boedie's topic in Tools, general discussion
I bet he made a knife.....- 27 replies
-
- blacksmith
- blacksmithing
- (and 6 more)
-
Like outside snap ring pliers?
-
Gasser Garage. Rebuild your forge or make it a HOTROD.
aessinus replied to Frosty's topic in Gas Forges
Ack, sorry boss, Fingers working faster than brain. Should have said "INSIDE" diameter. It was a 12" air tank from loooong ago. I did snort coffee though. Thanks for the Seattle Pottery Supply lead. I'll add that to my material vendor's list. -
Hay Budden Anvil Identification question
aessinus replied to redstone71's topic in Anvil Reviews by brand
At least in the 2nd photo it has scale under it, so that the corrosion should lay off a bit. -
Oh my... Is that a foot-vise I spy?
-
Gasser Garage. Rebuild your forge or make it a HOTROD.
aessinus replied to Frosty's topic in Gas Forges
Frosty says the question does belong here, not Burners 101. Here goes. I want to reline my forge & was wondering since 2" wool was recommended, why not 3"? I can stand to lose the 2" off the diameter. I've never used it without the firebrick volume eliminators. I'd also be interested to experiment with any new-fangled face coats that anyone has rumors of. My maintenance mgr at work wants me to get this one tuned up so he can duplicate it for the repair/r&d shop... -
How many links do you have in the length? I'll have to check this evening, but I seem to recall my old leather tugs have chain ends like that for attaching to a single-tree. Store-bought, fancy, pulling gear, maybe for shows/contests? Before tractor pulls there were draft pulls.... Gee, the size didn't click. My chains aren't near that big, but the fullers do look familiar.
-
I want (need) to use that material for my re-line. I'm a klutz. Also, since 2" of wool is the recommendation, why not 3"? Voted, btw. Should I move the question over there?
-
Slick rack, especially the extra legs for short stock. Are you aiming to put a little lean-to roof over it to keep the snow off?
-
wood stabilizing chambers
aessinus replied to Shamus Blargostadt's topic in Finish and Polish for Knives
Thx, JHCC, never heard of one, but HF has one for 25 bucks. Should save me hauling my supplies up to work (access to our handy shop oven vacuum). It might require some dithering over or adding a reservoir chamber as the gas releases from amongst the wood fibers. -
Mike, did you ever receive an answer? I can't, for love or money, locate anything regarding pricing on their site. Their order form even has a blank to populate. Their claim regarding the 311 foam blocks, "2000ºF, white hot, parts can be immersed in water with out cracking.", sounds awesome tough. As a material resource for work, I've just got to have some to trial. I can envision a forge for our tool fab shop....