Jump to content
I Forge Iron

Andrew Smith

Members
  • Posts

    101
  • Joined

  • Last visited

Contact Methods

  • Website URL
    http://icforge.com

Profile Information

  • Gender
    Male
  • Location
    Tyler, Texas
  • Interests
    Woodworking, Playing music, Metalworking, Leather crafting, Hunting, Fishing, Just Making and fixing things.

Converted

  • Location
    Van Texas

Recent Profile Visitors

6,858 profile views
  1. I usually use a belt sander with a 36 grit belt. Then a spokeshave or rasp to fine tune it.
  2. Thanks for the info. I will measure my dies tomorrow and see. I think the 25# is going to work well for me right now since it is still mostly just a hobby that makes a little money. I am not an expert but I am somewhat mechanically inclined and I had a feeling that this hammer could be hitting harder than what it was so I decided to do a little work. I am going to call Sid Tuesday -he is probably closed Monday for memorial day- and order me another spring and toggle arm. Have you ever seen anyone place the top clutch block about .2" closer so if you want the hammer to run slower then the top clutch is the only thing touching when you first press the treadle, thus allowing slightly more control. I read that somewhere but I can't remember where that was. -Andrew
  3. I think my dies are ok. When I bought the DVD from Sid, he sent me some papers and on one of the papers it said something to the effect that the dies for 25lb little giants are 3" tall. Is that 3" per die or 3" combined thickness for both? @ dsloan, can I increase the stock thickness that I can work by adjusting the pitman? I don't work anything larger than 2" very often but that would be something good to know, just in case.
  4. Ok guys, thanks for the help. Metalgnome, the right toggle arm is brazed and that was a question I was going to ask next. I have a spring guard but I took it off to take the pics. -Andrew
  5. I just went to the shop and realized that I might have just asked a sort of dumb question. By screwing in the bolt, it presses in a deal, I don't know what to call it, thus tensioning up the spring. But even with the bolt tightened all the way the spring is still loose enough to turn with my hand. I also have a second question, sometimes I will be running the hammer and I will have a hit, cycle around and miss, turn another cycle and have a soft tap then one more cycle and it will hit hard again and run normal for awhile. Is that because of the spring tension also?
  6. I bought a 25# little giant hammer a few weeks ago and I also bought Sid Suedmeier's DVD. The spring could use some adjustment but I don't know exactly what to do because mine is one of the new style hammers and Sid demonstrates how to adjust an early model hammer. My serial number starts with a 7, I can't remember the rest of it right now. The spring is loose enough that I can easily spin it barehanded and there is a small gap between the toggle arm and spring. I attached a pic to show what I mean. Thanks in advance. -Andrew
  7. I have made lots of tomahawks but I decided to make an axe so I made a Viking looking axe with a 7" wide blade. I used a wrap and weld method, I think that's what it is called, cold rolled steel wrapped around and a 1075 bit. On to the problem, I got the whole thing finished and started chopping and throwing it but there are a few places where the forge weld did not take right and the low carbon section of steel started to peel off of the bit. I wanted to know if I can salvage it and re-weld it or if I need to throw it in the "Mess-up" pile and start over.
  8. I was not planning on using wrought iron on this one. I know there are several ways of doing it and I was planning on maybe punching and drifting the eye but I am open to any suggestions. -Andrew
  9. I have made lots of tomahawks in the past but none of them had a blade wider than 4". I was wanting to make a viking axe with a blade around 7" wide. I can forge it but I just wanted to know the best way to do it and what size stock I should start with, hopefully save myself some trial-and-error. I attached a drawing of it. It is not perfect but you get the idea. -Andrew
  10. I have been looking around at presses and I was wondering what would work well for slitting and drifting. There are lots of different types but what do you think will work best and what are some prices on them? Thanks in advance. -Andrew
  11. I started with a BBQ pit forge, hair dryer, channel lock pliers, cross pein hammer and a vise with a small anvil on the back. Th forge eventually got so warped that I dug a hole in the ground and put the forge in the hole. I had to kneel down to work the fire and ran the air line underground. -Andrew
  12. Bruce Wilcock, really appreciate it, what is the best way for me to contact you about shipping and paying you? I was intending to only get a small amount for now just to try it out. winterbear, thanks for the link, I need something larger than 5/8" for tomahawks but I will remember that incase I need it for something else. -Andrew
  13. I know that wrought iron can be found at flea markets and antique shows but I don't know of many around here. I am wanting to start using wrought iron on some tomahawks and I was wonder if anyone knows where to buy it. I found this site, http://www.realwroughtiron.com/ Has anyone bought form here before or know anywhere that I can get it? Thanks for the help, -Andrew
  14. Ok, thanks for the help. I am gong to make one sometime in the near future. -Andrew
×
×
  • Create New...