Jump to content
I Forge Iron

G clamps


Recommended Posts

I tend to buy used at boot sales and jumbles (and sometimes at scrap yards).  They are on my "buy whenever a good one goes cheap" list as like pipe clamps you can never have enough!  (Worked in a custom woodshop once where we had a project that took all 100 of our pipe clamps *and* another hundred pipe clamps borrowed from another wood shop!)

 

Clamps marked China I only pick up off the side of the road free and tend to give them away or retire them in place in low stress jobs

 

With a large screw press I can even re-set sprung ones as long as the problem area is somewhere I can get the press to

Link to comment
Share on other sites

Maybe "Kant-Twist" clamps are good for machinests but they suck for fabrication as they simply dont generate any real force.   I use Bessey sliding F clamps, The heavy series ones I use generate 4 tons of clamping force.   the only C style clamps I use are heavy bridge clamps.       A 12" bridge clamp weighs 40 pounds and generates 20 tons of force.  (they also cost around $300 each)

Link to comment
Share on other sites

And Iron Dwarf I think you have some bad information.    Carver clamps are fantstic but they dont make any 10 ton rack clamps.    They are rated in daN.   The standard duty clamps produce about 2500 lbs of force and the big beefy heavy duty ones make about 6000 lbs of force.    The standard duty long reach ones are only good for 1250 pounds of squeeze.    The bar style clamps are even less.

 

That is one of the reasons I use the Besseys.     I like the Carver clamps but for the price the Besseys produce a lot more holding power.    The largest series of Besseys will produce 8500 pounds of squeeze, over a ton more than the Carver and they are less expensive.    For doing heavy work you need heavy clamps.    If your doing sheet metal or light duty work I suppose its unnessasary to have clamps that will pull together 3/4" plate when its got a 3/8" warp

 

I do wish the Carver clamps where a little more prevelent in the states.   I would like to have some of there part clamps and deep reach clamps but I worry about ordering them online.  I have bought clamps before that seemed like what I needed and then got them in my hand and they not been what I expected.   At a few hundred bucks a pop its hard to order them just to see.

 

 

post-2750-0-86544600-1406046495_thumb.jp

Link to comment
Share on other sites

MM- those Bessey F's are XXXX nice clamps!
I haven't used the Kant-Twist clamps with heavy vibration applications, so I can't comment on that.
But I really like them for machining and welding applications where nothing twists out of orientation when tightening, and the the self-aligning jaws are always parallel to what you're clamping in place. I'm sure you do a LOT larger scale stuff than I ever would, so I guess it is all in the application.

But I'm wondering about when you say the KT's don't generate any real clamping force. My catalog indicates a 12" capacity KT can make 6000 pounds of holding capacity.... you have to move up to the "Extra Heavy Duty" F-Clamps to get that much, and about 3x the price. A 10" KT is rated at 3500 pounds, still more than the Regular Duty F-clamps, and at a cheaper price. But I don't disagree that the F-clamps are very nice!

Link to comment
Share on other sites

the large carvers I have are 2" by 1" rack, standard reach ones of this type last time I looked ( a long time ago ) were listed as 10 tons.
in that series I have straight bars up to 4 foot long and clamps 6 foot long, with the smallest series of clamps I have from them I can squash 2" box section about 3/16 thick to 1" by 3".

in the small clamps I have 6" and 12" long and several straight bars that take the same heads and can be clamps or spreaders, have a few long and medium reach heads and clamps,

they are great, will post some pictures when I get time


for machine clamps I use lenkes german made clamps on T slot tables.

Link to comment
Share on other sites

IForgeIron Blueprints
Copyright 2002 - 2014 IFORGEIRON, All rights reserved

Clamps
by Glenn Conner


254.jpg
You have one heavy clamp but you have a project that needs two or more heavy clamps.

Your a blacksmith, make one.

253.jpg

All you need to do is to figure out what size stock you will need, then double the size. I figured that 1/2 inch square was about right so I used a piece of 1 inch square bar.

Just heat it up in the forge, make a couple of bends, and weld a nut on the end of the bar. A piece of all thread rod with a " T " welded on the end forms a handle to activate the screw. I figured that 1/2 inch all thread would work. If not, I can cut the weld and use heavier material for the screw.

Cost = zero, just using the materials in the resource center (scrap pile).

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...