Jump to content
I Forge Iron

Joel Worley

Members
  • Posts

    31
  • Joined

  • Last visited

Profile Information

  • Gender
    Male
  • Location
    Ohio
  • Interests
    Blade smithing , Black smithing

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Solseeker, I will try to get the drawings posted in the near future.
  2. It's been a while since I last posted any pictures. Here are some pictures of the toggle arms and pitman assembly in process. Also a shot of the idler arm and pulley on the linkage. The last picture is the hammer ready to run after getting the motor and belt on. I also posted a couple videos at the end. VID_20160711_190748.3gp VID_20160729_174728.3gp
  3. The crank plate and pulley are mounted and everything put back together. Things are still a little tight, so i will have to do some more scraping on the bearings. I opted to mount the pulley on the back of the hammer instead of the original center position. Due to the low ceiling in my shop, the motor will have to be mounted near the floor. Also, it will be a lot easier to take the drive belt off or replace it with the rear mounted pulley.
  4. The oil holes are drilled. I also had to mill out the excess babbitt material from the cap I over poured. A shot of the caps after painting. I cut some small grooves to help disperse oil evenly on the shaft and did a little scraping to even things up.
  5. Tomorrow, I will scrape the bearings to ensure even contact and get the bearing caps painted.
  6. A shot of one of the caps after pouring and the pour in progress. For never doing this before, It turned out really good.
  7. A few pine shims on the sides to keep the shaft centered. We put a piece of refractory wool on the shaft to protect the ratchet strap from the torch while preheating the shaft. Not pictured is the step of leveling an truing up the shaft to the face of the hammer and sooting the shaft. Just after the pour. Filled up good. Now to trim the excess the babbitt. A good full pour. The shims are in place for the proper spacing of the cap. The caps are in place and the gaps are plugged off with clay.
  8. Happy New Year! Today feels like a good day to pour the new babbitt bearings. Let the preheating begin. Here are the leather shims we made in place to get the bearing thickness needed.
  9. Jim Coke and ThomasPowers. Blacks Spring Sevice, They are in Zanesville Oh. I found them with a google search. Their number is (740)452-9256. Ask for Tom. I'll call and make sure they kept the drawing I sent them.
  10. I still need to fabricate a few more parts but other than that, the only thing I need is time to work on it.
  11. Thanks IronWolf. They did a great job. Including shipping, they charged me $185. I couldn't have made it myself for that price. If anyone needs a spring made, Blacks Spring Service in Ohio is the way to go.
  12. The spring came from the spring shop a full three inches wide. To make it match the original, I had to trim it down to 2 1/4" at the eyes. Doing this myself rather than paying the spring shop to do it saved me $90. The key ways are cut in the shaft and ready to go. Since the pulley was a little wobbled out, I had it bored, sleeved and a key way broached in with an extra set bolt on the opposite side. I don't think I will have any problems with it spinning on the shaft.
  13. I got the new shaft turned down today. Next I need to cut the key way for the crank plate.
  14. Hey Judson Yaggy, any chance you could get me some detailed measurements of the spring? Length of each leaf, distance center of eye to center of eye, width, belly depth and any other measurement you can think of. The guy that I asked to get the measurements for me is buried with orders and can't break loose to go to his friends shop to get them right away. Also it would be very helpful to get dimensions from more than one source. The spring shop that will be making the spring needs the best drawing and as many measurements that I can come up with. It would be much appreciated. Thanks.
×
×
  • Create New...