Bobby Campbell

Yea and all for only $35 I just couldn't pass it up.

Here is the before picture, when I first brought it home

I found this little beauty while at the local salvage yard digging up a trailer hitch for my truck. It was laying over in the dirt beside the weigh in scales. It was locked up when I bought it. I disassembled everything and wirebrushed all parts before putting it back together. I only found 2 markings on it, a number 6 on the inside edge of one of the jaws and a number 2 on the screw assembly. It now works very smoothly, it appears to be hand forged with the slots hot punched and you can see where the bends in the metal were made while forging. post 10.htm

Thanks Thomas, he seems to be enjoying it. asking a lot of questions and watching closely as I made the cuts for the birds mouths on the rafters. Here's some more pictures of todays progress. Ready to put the decking on top and get to nailing down shingles. The severe thunderstorms ran us inside so had to quit for the day. Its been over 20 years since I've done any kind of framing even so its turning out as planned. I have a few minor mistakes here and there but it is level, square and solid so that's a plus in my book.

I have started working on a shop area to hold my tools and stuff. Here's the progress after two days work (fighting the rain stinks). Day one was setting the 2x8 forms and 4x4 support posts. One side wall was laid out and framed in and set to the side for later use. Day two saw the 6x6 corner posts sunk 18 inches in the ground and set in concrete. All the holes were dug by hand with post hole digger and the mandatory rock bar. We also got the rest of the walls framed up and set. Everything squared and leveled, weather permitting we will start on the rafters tomorrow. (If the tornadoes stay away tonight and don't blow everything down). I didn't get a picture of the last wall to go up as it was dark and the rain ran us back into the house. I'll post it tomorrow if possible. It is 12ft x 16ft will have a 6 ft door opening on the South side and two 2ft x 4ft windows on the East and West sides. My 14 year old son is helping me which gives me the perfect opportunity to teach him how to frame simple structures. I will load more pictures as we progress with the build.

Frosty, Actually that's what I was trying to do was build a set of tongs =) They turned out ok I think for my first time forging anything. I still need to "pin them" and I drilled the hole cause I don't have a punch yet. Here's a pic of the tongs.....

Fired it up for the first time today. I couldn't wait until I had it lined so I did a test fire and beat on some stuff. Just worked on tapering a bit and trying to shape a tong side.

Just thought I would add my two coppers in this thread as I have direct experience with synthetic fabrics. When I was 13 or so I was in an unfortunate accident which involved fire. I was wearing those polyester sport socks, you know the knee length ones that have the colored bands at the top... Well suffice to say the fabric not only burned but it also melted to my right leg. Removal of the left over material made matters much worse. Third degree burns and several years of rehab later. I watch very closely what I'm wearing while working around heat.

Charles, I had honestly started my pan with a side blast in mind, but once I started my angles were all wrong and the sides didn't seem like they were steep enough to try and get a pipe to go through them. My fabrication skills leave a lot to be desired when figuring angles etc. Once I round up some more scrap sheet I'll make another attempt to see if I can get the next one cut right. I really would like to try our both types side/bottom. Just got stuck with bottom for now. I had planned on mudding up the pot quite a bit to close up some of the size and to protect the pot. I don't know the exact thickness but its pretty thin stuff. Think sheet metal they use to build guards around a drive belt system. It's definitely not ideal but hopefully it will work to let me heat smaller stuff. I appreciate both yours and Frosty's posts. Every time either of you reply to one of mine you impart more tidbits of info. I plan on digging around in the back yard tomorrow for some of our famous "red clay" weather permitting. I hope your dodging the worst of the storms that are blowing through tonight. We haven't gotten any bad winds yet but it has dumped a ton of water on us today.

Thank you for sharing this. awesome[ ˈôsəm ] ADJECTIVEadjective: awesomeextremely impressive or daunting; inspiring great admiration, apprehension, or fear: I think that definition fits this work very much!

Thanks Frosty, I have plenty of brick scraps to double it up. I may want to get it where I plan on using it first though as its already getting pretty heavy. I hope to have some extra cash coming my way in a month or so. I plan to use some of it to build a shed/shop. 12ftx12ft I think with two sides closed off to start. any bigger than that will take up too much room in the yard and might get the wife to yelling at me (wink).

DSW its 12"x14" and roughly 3" deep metal pan only. The brick I am using is roughly 1.5" thick and I have some more scrap pieces that are about 3x3x5" that I can put along the edges to build the fire deeper or I can mud it up to make it deeper. Will be using Charcoal to fire with (edit)

I work at a plant that uses a 150ft long rotary kiln and a few years back during a rebricking of the kiln I was able to obtain some of the scrap brick material. I have seriously been using this firebrick scrap as edging material around a flower bed for the last two years. First dry fitting of the firebrick...... That's as far as I have gotten today as severe thunderstorms fought me all day long off and on.

Here is a picture of the skilled labor I recruited to help me out. She's serious about hammering in that woodscrew (wink)

I then attached legs to the frame from the 4x4 scrap lumber I pilfered. And added a lip around the frame box (why will become apparent in my next post).