Bought my First Anvil!

[gauge]

Found an ad in a local paper for a 50 to 60 pound anvil. I was reluctant to call the seller because I thought this anvil would be way too small. I drove over and an old farmer took me out back behind his house where he had 2 anvils sitting outside in the weather. They were both about the same size. One had "Arm & Hammer" stamped on the side, and the other was an "M&H Armitage".

The A&H looked quite rusty and it appeared that someone welded a flat plate on top of the anvil. I am not sure if this normal or if it was later remanufactured. The surface was very flat and the edges were perfectly square.

The M&H had a less flat surface and slightly rounded edges, but it had minimal rust and looked more stout to me. Guy told me I could take my choice. I chose the M&H. We loaded it on my truck and I was thinking, either I have gotten really weak or this thing weighs a lot more than 50 to 60 pounds.

Took it home and looked at the stampings more closey. It says, "M&H Armitage Mouse Hole 1 . 0 . 26. I put it on a scale and it weighs 135 pounds! I was amazed that an anvil that sat outside in the weather had jut minimal surface rust.

Anyway, I don't know much about anvils. Is the M&H a good one? Would I have better off with the A&H?

I appreciate the feedback. Thanks!

[dablacksmith]

sounds like you got a great deal! if you can afford it (sounds like the price was right )see if you can get the other one also! the anvil you got sounds like a good one can you post pics?the main thing i do when looking over a anvil is take a hammer and tap the face in verious places and see how the hammer bounces .. you want a good bounce from all over the face but especially the center where you do most of your work . that said i will then ck flatness of face and ck the edges .. edges dont need to be perfectly sharp in fact a little rounded is good for most work. if it has all that going for it i consider it a "good " anvil if it has problems I figure worth accordingly. have fun!

[ThomasPowers]

Mouse hole is a great brand of traditionally made english anvils. The do have a squatter "industrial" look to them than many of the long horn and heeled american anvils but that is usually a bonus not a problem as it puts more of the anvil mass under the hammer rather than out in "tuning fork mode".

The english hundred weight system (CWT) goes: First number is hundredweights, 112 pounds, second number is quarter hundred weights, 28 pounds and the last number is pounds. So for anvils the second number must be 0-3 and the last 0-27

For your anvil that would be 1 x 112 + 0 x 28 + 26 = 138 pounds well within tolerance of bathroom scales and the old scales used in those times at the factory.

Now the Arm and Hammer anvil; was that stamped *in* or was it a logo that projected from the side? Two anvils manufacturers used the arm and hammer logo: vulcan that are a cast iron steel faced anvil with the logo projecting and Arm & Hammer that was a wrought iron steel faced anvil with the logo and writing stamped into the side. Arm & Hammers are *much* superior to vulcans *unless* sound is a major issue.

The things that can go wrong with traditionally made anvils are: delamination---test by tapping with a hammer and getting a dull sound or even buzzing rather than the "ting" and wearing through the face plate---not usually a big problem unless some idjit has ground the face down thinning the plate radically trying to get a dead flat/smooth surface---but trashing the anvil doing so and finally being in a structure fire that de-tempers the face making it soft---check for that with the bounce test.

Repairs can be done to anvils; several anvil manufacturers offered such services for used anvils re-forging them and forge welding on a new face. However many modern repairs do more dammage than they fix as most weldors and machinists don't know squat about anvils and so use the wrong techniques through ignorance. Some ABANA affiliates put on anvil repair workshops where folks that know what they are doing help out the rest of us.

Repairing an anvil usually drops it's price (as you don't know if it was done right or not), but may make it much more usefull to a smith.

Anvils are usually sold by weight so you may have got a real steal---how much did you give? If it was cheap you may want to try to buy the other one too.

Thomas

[gauge]

I am quite certain the A&H anvil is gone. The farmer told me that he got at least a dozen calls and that people were on the way when I arrived. I believe him. I've been looking for an anvil for years and usually within hours of an ad being placed, I would call and the anvil would be sold. I just got lucky because this anvil was very close to my house.

I paid $200 for it. I think that's a fair price.

If I remember correctly, the A&H had lettering that faced outwards, (not stamped inwards). For some reason the A&H just didn't feel good to me. To me, the A&H looked like some one took 3 pieces of metal and welded them together and then never bothered to grind off the ugly weld marks. The face on that anvil was perfectly flat - like no one ever took a hammer to it and the corners were very sharp. It looked like someone put a 3/8" piece of metal on top and welded it down. Maybe it is suppossed to look like that.

I should have brought a hammer with me so I could strike them and check for rebound.

Like I said, I know little about Anvils.

Thanks for thre responses, you guys are great! I'm looking forward to pounding some iron!

[Frosty]

Great deal.

Congratulations.

Frosty

[Thomas Dean]

Attaboy Guage!! You got a good anvil AND at a real good price! I love to hear of success stories like this one. Now, post pictures of your new treasure and we expect a few pictures of some thing you have made from this toy...er, I mean TOOL.

Now after reading this post would you please go to the top of the page and click on "user CP" and update your profile stating where you live. There could be one or more of us in your location that would be willing to meet you and swap lies...stories, yea, stories. Have fun.

[brucegodlesky]

Good deal Guage. I had a similar experience with a Mousehole. First anvil I bought. Never could get used to working on it. For some reason I just didn't like it. Finally peddled it off after I upgraded to a HayBudden I really liked. bruce/birdog

[gauge]

Originally Posted by Thomas Dean

Now after reading this post would you please go to the top of the page and click on "user CP" and update your profile stating where you live. There could be one or more of us in your location that would be willing to meet you and swap lies...stories, yea, stories. Have fun.

Thomas - How rude of me! I never properly introduced myself. I live in Southern New Jersey near Vineland and Milville. I work in Philadelphia as a Regional Finance Manager for a global consulting company.

I started restoring old cars when I was 13, and soon realized that a lot of parts can be fixed or made from scratch if you have the right tools, so I started to teach myself how to weld and I bought an Atlas lathe. In my opinion, the anvil is the oldest and most basic of metal working tools. Currently my "automotive" projects have been limited to old Land Cruiser and Mercedes Diesels.

I'll try and post some pictures of the anvil this weekend. I am away on business and I won't be back home until Friday.

By the way, before I left, the farmer that I bought the anvil from was both surprised and amused to see how happy I was with my purchase. He told me that he was sure he had at least one or two more anvils in one of his barns. He said he would look over the weekend, and if he could find them, he would call me. So, if he finds anything good in those barns, I might post pictures of more than one anvil. I'll keep you posted.

Thanks for having me as a member.

[Thomas Dean]

Cool! No telling what he'll find in the barn. I was given an old home made forge with a GREAT Buffalo blower that turns oh so smooth. I will probably scrap (as in use for something else) the forge as it is too heavy and really not made that well. I don't think it had been used. The man that gave it to me was pleased to do so as he knew it would be used. I told him what I planned to do with the forge part and he had no problem. (4x4x1/4 legs, frame from the same 3'sq with 1/4" plate filling the frame. Has 3" pipe for the ash and air. The thang weighs a ton! His goats had been playing on it for the past 8-10 yrs he said. ) Glad you're here.

[ThomasPowers]

If they stuck out then that is a Vulcan and not an Arm and Hammer; Vulcans use an arm and hammer logo though. Vulcans can look a bit off from their manufacturing method; but them some folks don't like Fishers either.

My two main shop anvils are a 500+# Fisher and the newly refurbished 407# Trenton so one is fat and squat and the other long and thin and I love them both! (though looking for tooling for 1.5" hardy holes is a bit harder than the 1" size.

US$200 for 135# Mousehole in decent shape on the east coast is considered quite good!

I'd call the guy back earlier and check on the others!