Quantcast Weird Shop Insulation - Blacksmith Forum
Blacksmith Forum

I Forge Iron

Blacksmith and Metalworking Forum

 

Weird Shop Insulation

This is a discussion on Weird Shop Insulation within the Shop tips and tricks forums, part of the General Discussions category; The other night I was clearing out some space in the garage. Looks like I'll be converting it to a ...


Go Back   Blacksmith Forum > General Discussions > Shop tips and tricks

Register FAQ Calendar Search Today's Posts Mark Forums Read

Notices

Reply

 

LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 11-29-2006, 05:32 PM
RegionalChaos's Avatar
Senior Member
 
Join Date: Jul 2006
Location: Drain, OR
Posts: 588
Default Weird Shop Insulation

The other night I was clearing out some space in the garage. Looks like I'll be converting it to a shop soon. Right now the garage isn't insulated. I'm not opposed to buying some insulation and putting it up, but a funny thought occurred to me so I thought I would ask about it. Do you guys think old neoprene would work to insulate a room? Say I had a whole truck load of old wet suits, or dry suits, or snow skiing suits, or something. Do you think that tacking up a few layers of it all around would do an OK job of insulating?
Reply With Quote
  #2 (permalink)  
Old 11-29-2006, 07:54 PM
Senior Member
 
Join Date: Mar 2005
Location: New Braunfels, Texas
Posts: 1,341
Default

I would want to know if there was a flammability issue before putting up too much of anything that might burn from a spark.
Reply With Quote
  #3 (permalink)  
Old 11-29-2006, 08:32 PM
RegionalChaos's Avatar
Senior Member
 
Join Date: Jul 2006
Location: Drain, OR
Posts: 588
Default

I think neoprene would just melt..
Reply With Quote
  #4 (permalink)  
Old 11-29-2006, 08:57 PM
clark-kentski's Avatar
Senior Member
 
Join Date: Aug 2006
Location: fort lauderdale,florida
Posts: 136
Default

if this is attached to your house dont do it! You woundt bust up your old couch and burn it in your living room fireplace would you ! of course not because you know the fumes will kill you! and to everyone else please ventilate your shop,big story today in florida about how many died running gas generator IN THEIR HOUSE!
Reply With Quote
  #5 (permalink)  
Old 11-30-2006, 02:01 AM
RegionalChaos's Avatar
Senior Member
 
Join Date: Jul 2006
Location: Drain, OR
Posts: 588
Default

Thanks for the warning. I understand the issues at hand..
Reply With Quote
  #6 (permalink)  
Old 11-30-2006, 08:50 AM
Candidquality's Avatar
Senior Member
 
Join Date: Nov 2005
Location: Mansfield Mills Blacksmith Shop, Tx
Posts: 281
Default

Interesting application of Neoprene. It would definitly be better than nothing as it would partially seal the area creating a air pocket that would be the actual insulating factor, but the particular design these are for(wetsuit) is designed to allow water(and this also air) through. I might use it to stop a draft or for a gasket material around a window. but not for a sheet of insulation. Now if you decide to use it to fill up a space inside the walls and it's shredded, it could actually be very effective (all that air trapped and movement restricted).
If you happen to get on that's designed for insulation it will have glass added to it (from 50 to 80 precent) and normally won't be able to be burned. But that wasn't what you mentioned.

As far as fire is concerned. it's a synthetic rubber wth a flash point of under 500 degrees(think tire). but you already know not to catch it on fire.
Reply With Quote
  #7 (permalink)  
Old 11-30-2006, 02:26 PM
Senior Member
 
Join Date: Mar 2005
Location: Rapid City, South Dakota
Posts: 617
Default

My recommendation would be to bite the bullet and buy commercially manufactured insulation. Neoprene will definately burn and will give off very toxic fumes when it does. The object of insulation is not only to keep the heat and/or cold where you want it, it is also helps to prevent the rapid spread of fire. That is not saying that all insulation is fire proof, but all the commercial stuff has been treated to be at least somewhat flame retardant. Think of all the valuable tools you will have in your shop and decide if you would want them protected by insulation that resists the rapid spread of fire or one that accelerates it. Remember that the cheapest thing we can get is often the most expensive thing we can own.

Woody
__________________
Never try to teach a pig to sing, it wastes your time and annoys the pig.

I do not suffer fools gladly.
Reply With Quote
  #8 (permalink)  
Old 11-30-2006, 09:23 PM
RegionalChaos's Avatar
Senior Member
 
Join Date: Jul 2006
Location: Drain, OR
Posts: 588
Default

Thanks for the feedback. The whole thought was more for kicks then anything I would really do. I'm not even sure yet that I will bother to insulate the garage. Oregon weather usually isn't that bad.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On
Forum Jump


All times are GMT -4. The time now is 02:29 AM.


Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.2.0