- Help with Heat Treating AR400 Steel
- Forging/shaping a D ring
- removing galvaniziation
- Getting an Anvil
- Blacksmith conference Madison Ga.
- Hand Crank Blower Repair Question?
- Makeing Babbitt Stick
- Rivet Header Snap
- rock buster? / post-hole digging tool
- Best tool for bending 1/2" to 3/4 rod
- Forge Weld Sparking
- Blacksmith - limited to a wheel chair
- Blacksmith - standing problems
- Side Drafting Kitty Litter
- Czech hammer handle...Resetting a handle-HELP
- Reverse letter stamps
- Mechanical PH brake material
- Buffalo Blower gearbox
- Chain Making Forge Welding
- ? on gas welding
- Any one know anything about blowers?
- Help with convave circle
- Metal cutting saws at reasonable prices?
- Carving gouge sweep
- Zinc Gas Danger???
- Whatzit
- split & drifts
- A2 damascus in a billet
- Hammer breaking ups and downs...
- Hot Chisels & Punches
- Forge Brick Question
- Diggin' Irons
- Oklahoma Coal
- Physics help
- Haulin Coal ?
- Champion 400 blower gasket?
- Understanding Basic Hydraulics
- To press or not to press (hydraulically speaking)
- Help selecting a anvil
- Mower Blade #'s
- Gas on the brain
- Large Quanity Finishing
- Silver Casting Question
- Anvil Refacing
- Water for Fule
- Blue print for an air gate?
- too small holes in fire grate?
- coal hard to keep alive
- doubts on a pipe (safety concerns)
- Need help
- Abusing an anvil
- Welding leads
- What to do with my Anvil
- Welding Table ?
- Muriatic acid and galvanization?
- Anvil differences??
- Snap Case
- Weighty solution to a problem
- Measuring tool
- Auxiliary anvil
- Tire Bolt Holder
- Tire tool
- A Quick Question on Stick Welders
- Forge smoke problem
- Assistance needed, Dallas area
- Is it called slag?
- Leakey Blower
- S-Curve in Square tubing.
- RR track anvil question
- Two Many
- What type of elctrode for arc welding?
- Stud removal my way
- Arc welding and magnetized objects
- Round nose pliers.
- Warning, Warning
- Mandrel
- Grate on rivet forge broke
- Is there an acceptable substitute for ITC 100
- Need advice on table legs
- Concave taper
- Help
- bending angled pieces
- Weathervane bearings
- Japanese power hammers
- blow out at 3500
- Whatzit? & iron supply North of Detroit.
- yet another what's it?
- another what is it
- New coal forge next to my parents white house
- quoting a circular staircase
- Charcoal Forges
- A what is it ????
- Important to all
- It's stuck Helen?
- ideas
- Gate problem...
- Any infor about an old Trenton??
- Food safe finish
- leaf spring snapped
- Increasing attendence at conferences
- Forge Hood Piping
- Anvil
- Rivets.
- Metal?
- Hand crank blower (Gear issue)
- Upsetting Block
- Is this crap?
- slick hammer handles
- Pie Chart
- homemade forge
- Hood on portable forge
- welding axe head
- museum wax
- How to get rid of mice?
- converting natural gas to propane
- Reil burner problem
- Sick MIG
- tapered flat bar bands
- single hits with power hammer?
- 18th Century Toaster? How did they do it?
- Tandem Trailer
- MICA material
- What are Go - No Go Gauges?
- shipping
- Help identify a tool for me....
- What is it?
- risk assessment forms
- Anchoring gate into stone
- What if you,
- Slack tubs in freezing weather
- fire bricks
- Tool for repetitive cuts of 5/8 SST round bar
- Stake Holder table design help needed.
- jackhammer bits
- railwagon axle
- Sheet Metal Thickness vs Gauge Sizes
- ellectrifying
- Shears/stock cutter ID?
- used forge worth the cost?
- Anvil ID & fix up question
- Anvil help
- OT - Pewter beer stein
- dent removal
- Plasma cutter air requisits
- resurfacing an anvil
- quality coal needed
- Removing powder coat from car springs
- Working Short Pieces of Tool Steel
- Burning Chrome
- Attitude
- How much force required?
- Burning Chrome
- I - Beam construction - load limits
- VW Forge on wheels?
- Simple solution for a common ailment
- Metric Conversion Calculator
- ''WARPED'' Plate
- "faststeel"??
- Product Liability Insurance - any suggestions?
- Pit Bull Mig
- smithing courses\shools?
- Steam Hammer valve rebuilding and clearence, Rod replacement
- And I'm out
- ironwork used as toy´s?
- rail road spikes
- plastic steel in a cylinder
- Question about Metal Polebarns, and power hammers???
- Welder problem
- Help Identify this
- do you temper a shovel or hoe?
- Loosing heat when localize cooling
- Drilling Jigs
- Help with projects
- Bell mechanisms
- Mechanics Pry Bar ??
- Demagnatizing a needle
- apprentise
- Making hardie tools
- new forge pan
- Forging and fitting bands to wooden mallets?
- Blower for an air curtain?
- Flat Table Top
- Moving a building
- making torsion bar springs
- Preventative maintance
- Machining a DEEP square hole
- foot vise
- question about annealing and tempering
- Solution to aluminum wire welding to mig tip
- What is it?
- tempering flint strikers
- welding D2 steel
- mower blade
- How to make a collar
- what brass to use for forgings?
- What's it
- plasma cutter explained maybe
- Fire Screen Assy
- What is that? clip
- gas forge with Reid burner trying to get it to burn right.
- What is this used for? Pliers?
- how many sq. inches will a Reid burner heat properly
- making belt sander
- Anvil Shopping and forge quetion
- OT - Machinery Repair ?
- Gas forge
- scaling
- Feathers
- Another quick tip
- Quick tips
- Kandle Kup Kink
- Odd color on my anvil
- Forging under canvas
- Where have all the pictures gone?
- Unknown Tool